LAN9116-MT SMSC, LAN9116-MT Datasheet - Page 89
![IC ETHERNET CTRLR 10/100 100TQFP](/photos/6/82/68210/lan9116-mt_sml.jpg)
LAN9116-MT
Manufacturer Part Number
LAN9116-MT
Description
IC ETHERNET CTRLR 10/100 100TQFP
Manufacturer
SMSC
Datasheet
1.LAN9116-MT.pdf
(132 pages)
Specifications of LAN9116-MT
Controller Type
Ethernet Controller
Interface
Serial EEPROM
Voltage - Supply
3.3V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
100-TQFP, 100-VQFP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Supply
-
Other names
638-1011
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LAN9116-MT
Manufacturer:
XCEIVE
Quantity:
3 400
Company:
Part Number:
LAN9116-MT
Manufacturer:
Standard
Quantity:
2 245
Company:
Part Number:
LAN9116-MT
Manufacturer:
Microchip Technology
Quantity:
10 000
Part Number:
LAN9116-MT
Manufacturer:
SMSC
Quantity:
20 000
Highly Efficient Single-Chip 10/100 Non-PCI Ethernet Controller
Datasheet
SMSC LAN9116
5.3.22
31:24
23:16
BITS
15:8
7:4
3
2
1
DESCRIPTION
Reserved
Automatic Flow Control High Level (AFC_HI). Specifies, in multiples of
64 bytes, the level at which flow control will trigger. When this limit is
reached the chip will apply back pressure or will transmit a pause frame as
programmed in bits [3:0] of this register.
During full-duplex operation only a single pause frame is transmitted when
this level is reached. The pause time transmitted in this frame is
programmed in the FCPT field of the FLOW register in the MAC CSR space.
During half-duplex operation each incoming frame that matches the criteria
in bits [3:0] of this register will be jammed for the period set in the
BACK_DUR field.
Automatic Flow Control Low Level (AFC_LO). Specifies, in multiples of
64 bytes, the level at which a pause frame is transmitted with a pause time
setting of zero. When the amount of data in the RX data FIFO falls below
this level the pause frame is transmitted. A pause time value of zero
instructs the other transmitting device to immediately resume transmission.
The zero time pause frame will only be transmitted if the RX data FIFO had
reached the AFC_HI level and a pause frame was sent. A zero pause time
frame is sent whenever automatic flow control in enabled in bits [3:0] of this
register.
Note:
Backpressure Duration (BACK_DUR). When the LAN9116 automatically
asserts back pressure, it will be asserted for this period of time. This field
has no function and is not used in full-duplex mode. Please refer to
Table
information.
Flow Control on Multicast Frame (FCMULT). When this bit is set, the
LAN9116 will assert back pressure when the AFC level is reached and a
multicast frame is received. This field has no function in full-duplex mode.
Flow Control on Broadcast Frame (FCBRD). When this bit is set, the
LAN9116 will assert back pressure when the AFC level is reached and a
broadcast frame is received. This field has no function in full-duplex mode.
Flow Control on Address Decode (FCADD). When this bit is set, the
LAN9116 will assert back pressure when the AFC level is reached and a
frame addressed to the LAN9116 is received. This field has no function in
full-duplex mode.
AFC_CFG – Automatic Flow Control Configuration Register
This register configures the mechanism that controls both the automatic, and software-initiated
transmission of pause frames and back pressure.
Note: The LAN9116 will not transmit pause frames or assert back pressure if the transmitter is
5.5, describing Backpressure Duration bit mapping for more
Offset:
When automatic flow control is enabled the AFC_LO setting must
always be less than the AFC_HI setting.
disabled.
ACh
DATASHEET
89
Size:
32 bits
TYPE
R/W
R/W
R/W
R/W
R/W
R/W
RO
Revision 1.5 (07-11-08)
DEFAULT
00h
00h
0h
0
0
0
-