CS4265-CNZ Cirrus Logic Inc, CS4265-CNZ Datasheet - Page 27

• Manufacturer Part Number: CS4265-CNZ
• Description: IC CODEC 24BIT 104DB 32QFN
• Manufacturer: Cirrus Logic Inc
• Type: Stereo Audior

Specifications of CS4265-CNZ

• Package / Case: 32-QFN
• Data Interface: PCM Audio Interface
• Resolution (bits): 24 b
• Number Of Adcs / Dacs: 2 / 2
• Sigma Delta: Yes
• Dynamic Range, Adcs / Dacs (db) Typ: 104 / 104
• Voltage - Supply, Analog: 3.13 V ~ 5.25 V
• Voltage - Supply, Digital: 3.13 V ~ 5.25 V
• Operating Temperature: -10°C ~ 70°C
• Mounting Type: Surface Mount
• Number Of Adc Inputs: 4
• Number Of Dac Outputs: 2
• Conversion Rate: 192 KSPS
• Interface Type: Serial (I2S)
• Resolution: 24 bit
• Operating Supply Voltage: 3.3 V, 5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 10 C
• Number Of Channels: 2 ADC/2 DAC
• Thd Plus Noise: - 95 dB ADC / - 90 dB DAC
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 598-1001 - BOARD EVAL FOR CS4265 CODEC
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 598-1039

DS657F2
4.6
4.7
4.7.1
4.7.2
4.7.3
Output Connections
The CS4265 DACs implement a switched-capacitor filter, followed by a continuous time low-pass filter. Its
response, combined with that of the digital interpolator, is shown in
page
The CS4265 DAC does not include phase or amplitude compensation for an external filter. Therefore, the
DAC system phase and amplitude response is dependent on the external analog circuitry.
Output Transient Control
The CS4265 uses Popguard
power-down. This technique eliminates the audio transients commonly produced by single-ended, single-
supply converters when it is implemented with external DC-blocking capacitors connected in series with the
audio outputs. To make best use of this feature, it is necessary to understand its operation.
topology. If pseudo-differential input functionality is not required, simply connect the SGND pin to AGND
through the parallel combination of a 10 µF and a 0.1 µF capacitor.
Power-Up
When the device is initially powered-up, the DAC outputs AOUTA and AOUTB are clamped to VQ, which
is initially low. After the PDN bit is released (set to ‘0’), the outputs begin to ramp with VQ towards the
nominal quiescent voltage. This ramp takes approximately 200 ms to complete. The gradual voltage
ramping allows time for the external DC-blocking capacitors to charge to VQ, effectively blocking the qui-
escent DC voltage. Audio output will begin after approximately 2000 sample periods.
Power-Down
To prevent audio transients at power-down, the DC-blocking capacitors must fully discharge before turn-
ing off the power. In order to do this, either the PDN should be set or the device should be reset about
250 ms before removing power. During this time, the voltage on VQ and the DAC outputs will gradually
discharge to GND. If power is removed before this 250 ms time period has passed, a transient will occur
when the VA supply drops below that of VQ. There is no minimum time for a power cycle; power may be
re-applied at any time.
Serial Interface Clock Changes
When changing the clock ratio or sample rate, it is recommended that zero data (or near zero data) be
present on the selected SDIN pin for at least 10 LRCK samples before the change is made. During the
47”. The recommended external analog circuitry is shown in the Typical Connection Diagram.
S G N D
A IN A
A IN B
N ote: If pseudo-differential input functionality is not required, the
Figure 12. Pseudo-Differential Input Stage
®
connections shown with dashed line should be added.
technology to minimize the effects of output transients during power-up and
10 µF
0.1 µF
V A
CS4265
-
+
+
-
In to P G A
In to P G A
Section 8. “DAC Filter Plots” on
CS4265
27