MPC8313CVRADDB Freescale Semiconductor, MPC8313CVRADDB Datasheet - Page 44

• Manufacturer Part Number: MPC8313CVRADDB
• Description: MPU POWERQUICC II PRO 516-PBGA
• Manufacturer: Freescale Semiconductor

Specifications of MPC8313CVRADDB

• Processor Type: MPC83xx PowerQUICC II Pro 32-Bit
• Speed: 267MHz
• Voltage: 0.95 V ~ 1.05 V
• Mounting Type: Surface Mount
• Package / Case: 516-PBGA
• Processor Series: MPC8xxx
• Core: e300
• Data Bus Width: 32 bit
• Development Tools By Supplier: MPC8313E-RDB
• Maximum Clock Frequency: 400 MHz
• Operating Supply Voltage: - 0.3 V to + 1.26 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Data Ram Size: 16 KB
• I/o Voltage: 2.5 V
• Interface Type: I2C, SPI, UART
• Minimum Operating Temperature: - 40 C
• Program Memory Type: EEPROM/Flash
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

High-Speed Serial Interfaces (HSSI)
The other detailed AC requirements of the SerDes reference clocks is defined by each interface protocol
based on application usage. Refer to the following section for detailed information:
9.2.4.1
SD_REF_CLK/SD_REF_CLK are not intended to be used with, and should not be clocked by, a spread
spectrum clock source.
44
At recommended operating conditions with XV
Rising edge rate (SDn_REF_CLK) to falling edge rate
(SDn_REF_CLK) matching
Notes:
1. Measurement taken from single-ended waveform.
2. Measurement taken from differential waveform.
3. Measured from –200 to +200 mV on the differential waveform (derived from SD n _REF_CLK minus SD n _REF_CLK). The
4. Matching applies to rising edge rate for SD n _REF_CLK and falling edge rate for SD n _REF_CLK. It is measured using a
signal must be monotonic through the measurement region for rise and fall time. The 400 mV measurement window is
centered on the differential zero crossing. See
200 mV window centered on the median cross point, where SD n _REF_CLK rising meets SD n _REF_CLK falling. The median
cross point is used to calculate the voltage thresholds the oscilloscope is to use for the edge rate calculations. The rise edge
rate of SD n _REF_CLK should be compared to the fall edge rate of SD n _REF_CLK, the maximum allowed difference should
not exceed 20% of the slowest edge rate. See
•
SD n _REF_CLK
SD n _REF_CLK
V
V
IH
IL
SD n _REF_CLK
SD n _REF_CLK
SD n _REF_CLK
V
Section 8.3.2, “AC Requirements for SGMII SD_REF_CLK and SD_REF_CLK”
= +200 mV
= –200 mV
CROSS MEDIAN
Minus
0.0 V
Spread Spectrum Clock
Figure 32. Single-Ended Measurement Points for Rise and Fall Time Matching
Table 40. SerDes Reference Clock Common AC Parameters (continued)
MPC8313E PowerQUICC
Figure 31. Differential Measurement Points for Rise and Fall Time
Parameter
Rise Edge Rage
DD_SRDS1
™
Figure
Figure
or XV
II Pro Processor Hardware Specifications, Rev. 3
DD_SRDS2
31.
32.
V
V
CROSS MEDIAN
CROSS MEDIAN
= 1.0 V ± 5%.
matching
Symbol
Rise-fall
SD n _REF_CLK
SD n _REF_CLK
V
CROSS MEDIAN
+ 100 mV
– 100 mV
Min
—
Fall Edge Rate
T
FALL
Max
20
Freescale Semiconductor
T
RISE
Unit
%
Notes
1, 4