MPC8313VRADDB Freescale Semiconductor, MPC8313VRADDB Datasheet - Page 96

• Manufacturer Part Number: MPC8313VRADDB
• Description: MPU POWERQUICC II PRO 516-PBGA
• Manufacturer: Freescale Semiconductor

Specifications of MPC8313VRADDB

• Processor Type: MPC83xx PowerQUICC II Pro 32-Bit
• Speed: 267MHz
• Voltage: 0.95 V ~ 1.05 V
• Mounting Type: Surface Mount
• Package / Case: 516-PBGA
• Processor Series: MPC8xxx
• Core: e300
• Data Bus Width: 32 bit
• Development Tools By Supplier: MPC8313E-RDB
• Maximum Clock Frequency: 400 MHz
• Operating Supply Voltage: - 0.3 V to + 1.26 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Data Ram Size: 16 KB
• I/o Voltage: 2.5 V
• Interface Type: I2C, SPI, UART
• Minimum Operating Temperature: - 40 C
• Program Memory Type: EEPROM/Flash
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Document Revision History
96
Number
Rev.
1
0
3/2008
6/2007
Date
MPC8313E PowerQUICC
Initial release.
• In Table 63, added LBC_PM_REF_10 & LSRCID3 as muxed with USBDR_PCTL1
• In Table 63, added LSRCID2 as muxed with USBDR_PCTL0
• In Table 63, added LSRCID1 as muxed with USBDR_PWRFAULT
• In Table 63, added LSRCID0 as muxed with USBDR_DRIVE_VBUS
• In Table 63, moved T1, U2,& V2 from V
• In Table 63, moved P2, R2, & T3 from V
• In Table 63, moved P5, & U4 from V
• In Table 63, moved P3, & V4 from V
• In Table 63, removed “Double with pad” for AV
• In Table 63, added impedance control requirements for SD_IMP_CAL_TX (100 ohms to GND) and
• In Table 63, updated muxing in pinout to show new options for selecting IEEE 1588 functionality.
• In Table 63, updated muxing in pinout to show new LBC ECC boot enable control muxed with
• Added pin type information for power supplies.
• Removed N1 and N3 from Vss section of Table 63. Added Therm0 and Therm1 (N1 and N3,
• In Table 65 corrected maximum frequency of Local Bus Frequency from “33–66” to 66 MHz
• In Table 65 corrected maximum frequency of PCI from “24–66” to 66 MHz
• Added “which is determined by RCWLR[COREPLL],” to the note in Section 20.2, “Core PLL
• Added “(VCOD)” next to VCO divider column in Table 68. Added footnote stating that core_clk
• In Table 69, notes were confusing. Added note 3 for VCO column, note 4 for CSB ( csb_clk ) column,
• In Table 69, updated note 6 to specify USB reference clock frequencies limited to 24 and 48 for rev.
• Replaced Table 71 “Thermal Resistance for TEPBGAII with Heat Sink in Open Flow”.
• Removed last row of Table 19.
• Removed 200 MHz rows from Table 21 and Table 5.
• Changed VIH minimum spec from 2.0 to 2.1 for clock, PIC, JTAG, SPI, and reset pins in Table 9,
• Added Figure 4 showing the DDR input timing diagram.
•
• Added “and power” to rows 2 and 3 in Table 10
• Added the sentence “Once both the power supplies...” and PORESET to Section 2.2, “Power
• In Figure 35, corrected “USB0_CLK/USB1_CLK/DR_CLK” with “USBDR_CLK”
• In Table 42, clarified that AC specs are for ULPI only.
and Ground Supplies section
SD_IMP_CAL_RX (200 ohms to GND).
Added footnote 8
eTSEC1_MDC
respectively). Added note 7 to state: “Internal thermally sensitive resistor, resistor value varies
linearly with temperature. Useful for determining the junction temperature.”
Configuration” about the VCO divider.
frequency must not exceed its maximum, so 2.5:1 and 3:1 core_clk:csb_clk ratios are invalid for
certain csb_clk values.
note 5 for USB ref column, and note 6 to replace “Note 1”. Clarified note 4 to explain erratum
eTSEC40.
2 silicon.
Table 47, Table 54, Table 59, and Table 61.
In Table 19, removed “MDM” from the “M
column for the tCISKEW parameter. MDM is an output signal and should be removed from
the input AC timing spec table (tCISKEW).
Sequencing,” and Figure 3.
Table 73. Document Revision History (continued)
™
II Pro Processor Hardware Specifications, Rev. 3
SS
Substantive Change(s)
DD
to XPADVSS.
DD
to XPADVDD.
SS
DQS-MDQ/MECC/MDM” text under the Parameter
to XCOREVDD.
to XCOREVSS.
DD1
and AV
DD2
and moved AV
Freescale Semiconductor
DD1
and AV
DD2
to Power