CY7C63723-PC Cypress Semiconductor Corp, CY7C63723-PC Datasheet - Page 21

• Manufacturer Part Number: CY7C63723-PC
• Description: IC MCU 8K LS USB/PS-2 18-DIP
• Manufacturer: Cypress Semiconductor Corp
• Series: enCoRe™r

Specifications of CY7C63723-PC

• Applications: USB Microcontroller
• Core Processor: M8B
• Program Memory Type: OTP (8 kB)
• Controller Series: CY7C637xx
• Ram Size: 256 x 8
• Interface: PS2, USB
• Number Of I /o: 10
• Voltage - Supply: 4 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Through Hole
• Package / Case: 18-DIP (0.300", 7.62mm)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: 428-1322

17.0
SPI is a four-wire, full-duplex serial communication interface
between a master device and one or more slave devices. The
CY7C637xx SPI circuit supports byte serial transfers in either
Master or Slave modes. The block diagram of the SPI circuit
is shown in Figure 17-1. The block contains buffers for both
The SPI Data Register below serves as a transmit and receive
buffer.
Bit [7:0]: Data I/O[7:0]
17.1
Only an SPI Master can initiate a byte/data transfer. This is
done by the Master writing to the SPI Data Register. The
Master shifts out 8 bits of data (MSB first) along with the serial
clock SCK for the Slave. The Master’s outgoing byte is
replaced with an incoming one from a Slave device. When the
last bit is received, the shift register contents are transferred
to the receive buffer and an interrupt is generated. The receive
data must be read from the SPI Data Register before the next
byte of data is transferred to the receive buffer, or the data will
be lost.
Document #: 38-08022 Rev. *B
Read/Write R/W R/W R/W R/W R/W R/W R/W R/W
Bit Name
Writes to the SPI Data Register load the transmit buffer,
while reads from this register read the receive buffer con-
tents.
1 = Logic HIGH
0 = Logic LOW
Reset
Bit #
Figure 17-2. SPI Data Register (Address 0x60)
Operation as an SPI Master
Serial Peripheral Interface (SPI)
7
0
6
0
5
0
Data I/O
4
0
Data Bus
FOR
FOR
8 bit shift register
3
0
Data Bus
RX Buffer
TX Buffer
2
0
Figure 17-1. SPI Block Diagram
Write
1
0
Read
0
0
transmit and receive data for maximum flexibility and
throughput. The CY7C637xx can be configured as either an
SPI Master or Slave. The external interface consists of
Master-Out/Slave-In (MOSI), Master-In/Slave-Out (MISO),
Serial Clock (SCK), and Slave Select (SS).
SPI modes are activated by setting the appropriate bits in the
SPI Control Register, as described below.
When operating as a Master, an active LOW Slave Select (SS)
must be generated to enable a Slave for a byte transfer. This
Slave Select is generated under firmware control, and is not
part of the SPI internal hardware. Any available GPIO can be
used for the Master’s Slave Select output.
When the Master writes to the SPI Data Register, the data is
loaded into the transmit buffer. If the shift register is not busy
shifting a previous byte, the TX buffer contents will be automat-
ically transferred into the shift register and shifting will begin.
If the shift register is busy, the new byte will be loaded into the
shift register only after the active byte has finished and is trans-
ferred to the receive buffer. The new byte will then be shifted
out. The Transmit Buffer Full (TBF) bit will be set HIGH until
the transmit buffer’s data-byte is transferred to the shift
register. Writing to the transmit buffer while the TBF bit is HIGH
will overwrite the old byte in the transmit buffer.
The byte shifting and SCK generation are handled by the
hardware (based on firmware selection of the clock source).
Data is shifted out on the MOSI pin (P0.5) and the serial clock
is output on the SCK pin (P0.7). Data is received from the slave
on the MISO pin (P0.6). The output pins must be set to the
desired drive strength, and the GPIO data register must be set
to 1 to enable a bypass mode for these pins. The MISO pin
must be configured in the desired GPIO input mode. See
Section 12.0 for GPIO configuration details.
17.2
The Master’s SCK is programmable to one of four clock
settings, as shown in Figure 17-1. The frequency is selected
with the Clock Select Bits of the SPI control register. The
Master SCK Selection
Internal SCK
Master
/ Slave
Control
4
MOSI
MISO
SCK
SS
CY7C63722
CY7C63723
CY7C63743
Page 21 of 49