20-101-1258 Rabbit Semiconductor, 20-101-1258 Datasheet - Page 138

• Manufacturer Part Number: 20-101-1258
• Description: COMPUTER SINGLE-BOARD BL4S160
• Manufacturer: Rabbit Semiconductor

Specifications of 20-101-1258

• Module/board Type: Single Board Computer Module
• Product: Modules
• Processor Type: Rabbit 4000
• Sram: 1 MB
• Flash: 2 MB
• Timers: 8 bit, 10 bit
• Number Of I/os: 20
• Backup Battery: 3 V Lithium Coin Type
• Operating Voltage: 9 V to 36 V
• Board Size: 96 mm x 146 mm x 16 mm
• Description/function: Computer Module
• For Use With/related Products: BL4S160
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 316-1171

Continue the following steps with the Digi
Since the ZigBee Utility
ZigBee Utility if it is running.
1. Start X-CTU from the desktop icon and set the “PC Settings” tab to
2. On the “PC Settings” tab, check the “Enable API” box under “Host Setup.”
3. On the “PC Settings” tab, select the “USB Serial Port” corresponding to the USB serial
4. Under the “Modem Configuration” tab click the “Read” button. X-CTU will now display
5. Now set the networking parameters in your project defines or in the sample program to
6. Finish by clicking the “Write” button.
F.2.1 Additional Reference Information
Check
module, the X-CTU utility, and the Digi
BL4S100 User’s Manual
HARDWARE
port the Digi
response showing the Modem Type (XB 24-B) and the firmware version. Click
Note that several USB serial ports could be listed. If you select a serial port without the
Digi
cation with modem … OK,” but the modem type will be unknown, and the firmware
version will be blank.
If you a get a message that X-CTU is unable to open the COM port, verify that you
selected the COM port with the “USB Serial Port,” then try unplugging the Digi
USB from the USB slot and plugging it back in. Now click “Test/Query” again.
the networking and I/O parameters for the Digi
coordinator.
match the parameters in the Dynamic C
library.
Modem: XBEE XB24-ZB
Function Set: ZIGBEE COORDINATOR API (do not select other settings)
Version: the version of the firmware included with the version of Dynamic C you are using (should be
Networking
Digi’s Web site
®
of the type 21…)
(D) CH - Operating Channel — this is the operating channel you could see when you ran the
AT_INTERACTIVE.C
ing the command ATCH <Enter>. This channel information cannot be changed from the X-CTU
utility.
(0123456789ABCDEF) ID - Extended Pan ID — set the new extended PAN ID that follows 0x to
match the
(1FFE) SC - Scan Channels - set the new value for the channels to scan, E, for example, to match
the new setting in the macro.
#define DEFAULT_CHANNELS 0x000E
XBee USB connected, the X-CTU response to “Test/Query.” will be “communi-
®
DEFAULT_EXTPANID
flow control,
XBee USB is connected to and click “Test/Query.” You should see a
for the latest information and documentation on the XBee Series 2
XBEE_GPIO_GUI.exe
sample program in the Dynamic C
8
data bits, parity
macro.
®
XBee USB. Note that the XBee™ and the XBee
®
LIB\Rabbit4000\XBee\XBEE_API.LIB
XBee USB connected to your PC’s USB port.
will conflict with X-CTU, first close the
NONE
®
XBee USB being used as the ZigBee
,
1
stop bit.
SAMPLES\XBEE
115200
folder by enter-
baud,
®
OK
XBee
.
136