20-101-1258 Rabbit Semiconductor, 20-101-1258 Datasheet - Page 111

• Manufacturer Part Number: 20-101-1258
• Description: COMPUTER SINGLE-BOARD BL4S160
• Manufacturer: Rabbit Semiconductor

Specifications of 20-101-1258

• Module/board Type: Single Board Computer Module
• Product: Modules
• Processor Type: Rabbit 4000
• Sram: 1 MB
• Flash: 2 MB
• Timers: 8 bit, 10 bit
• Number Of I/os: 20
• Backup Battery: 3 V Lithium Coin Type
• Operating Voltage: 9 V to 36 V
• Board Size: 96 mm x 146 mm x 16 mm
• Description/function: Computer Module
• For Use With/related Products: BL4S160
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 316-1171

The XBee sample programs in the Dynamic C
the use of the XBee function calls.
•
•
•
BL4S100 User’s Manual
SLEEP.C
Rabbit up upon receipt of a packet.
It also demonstrates conditional use of TCP/IP networking in low-power modes. The
sample program illustrates how to respond to TCP/IP ping packets and also demon-
strates pinging a remote host. It prints a message in the Dynamic C
when the ping response arrives here.
Once the sample program is compiled and running, open your PC Web browser. As
long as you have not modified the
the following server address in your Web browser to bring up the Web page served by
the sample program.
If
routers and coordinators cannot sleep.
XBEE_GPIO_SERVER.C
and clusters. It is meant to be run with the Windows GUI client (installed in Dynamic C’s
Utilities
sample program (
RabbitCore module or on a single-board computer with an XBee RF module.
Connect the BL4S100/BL4S150 to the Demonstration Board as explained in Section 6.2.1.
Then compile and run this sample program on the BL4S100/BL4S150. Run the Windows
GUI client (
folder) on your PC. Configure the GUI client to connect to the Digi USB XBee coordi-
nator and scan for devices. Make sure the BL4S100/BL4S150 and the Digi USB XBee
coordinator are configured with the same PAN ID.
If you run the
RF module, set the PAN IDs to match between the client and the server sample programs.
Now select the GPIO server and use the GUI interface on the PC, or the command-line
client on another XBee-equipped board to view the server's inputs and change its outputs.
For example, you can toggle the LEDs on the Demonstration Board on/off.
XBEE_WEB_GATEWAY.C
wireless ZigBee network through a Web interface.
Before you compile and run this sample program, set up a ZigBee network based on
boards with the XBee RF module. The sample program provides configuration recom-
mendations for RF Interface Boards from the Mesh Network Add-On Kit and other
boards. Use the X-CTU utility to configure these boards as end devices with the same
PAN ID.
For this sample, the
http://10.10.6.100
PING_WHO
—This sample program demonstrates having the XBee RF module wake the
XBEE_GPIO_GUI.exe
directory) and a Digi USB XBee coordinator or with the GPIO client
is not defined, then it pings the default gateway.
XBEE_GPIO_CLIENT.C
SAMPLES/XBEE/XBEE_GPIO_CLIENT.C
XBEE_ROLE
—This sample program shows how to set up and use endpoints
—This sample program shows how to interact with nodes on a
macro must be defined as
TCPCONFIG 1
in the Dynamic C
sample program on another board with an XBee
SAMPLES\BL4S1xx\XBee
macro in the sample program, enter
Utilities\XBee GPIO GUI
) running on an RCM4510W
NODE_TYPE_ENDDEV
STDIO
folder illustrate
window
since
109