EP4CGX150CF23I7 Altera, EP4CGX150CF23I7 Datasheet - Page 184
EP4CGX150CF23I7
Manufacturer Part Number
EP4CGX150CF23I7
Description
IC CYCLONE IV FPGA 150K 484FBGA
Manufacturer
Altera
Series
CYCLONE® IV GXr
Datasheets
1.EP4CGX15BN11C8N.pdf
(44 pages)
2.EP4CGX15BN11C8N.pdf
(14 pages)
3.EP4CGX15BN11C8N.pdf
(478 pages)
4.EP4CGX15BN11C8N.pdf
(10 pages)
Specifications of EP4CGX150CF23I7
Number Of Logic Elements/cells
149760
Number Of Labs/clbs
9360
Total Ram Bits
6480000
Number Of I /o
270
Voltage - Supply
1.16 V ~ 1.24 V
Mounting Type
Surface Mount
Operating Temperature
-40°C ~ 100°C
Package / Case
484-FBGA
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Number Of Gates
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
EP4CGX150CF23I7
Manufacturer:
ALTERA
Quantity:
3 000
Part Number:
EP4CGX150CF23I7N
Manufacturer:
ALTERA/阿尔特拉
Quantity:
20 000
- EP4CGX15BN11C8N PDF datasheet
- EP4CGX15BN11C8N PDF datasheet #2
- EP4CGX15BN11C8N PDF datasheet #3
- EP4CGX15BN11C8N PDF datasheet #4
- Current page: 184 of 478
- Download datasheet (13Mb)
8–18
Cyclone IV Device Handbook, Volume 1
f
f
1
Programming Serial Configuration Devices
Serial configuration devices are non-volatile, flash memory-based devices. You can
program these devices in-system with the USB-Blaster™ or ByteBlaster™ II download
cables. Alternatively, you can program them with the Altera Programming Unit
(APU), supported third-party programmers, or a microprocessor with the SRunner
software driver.
You can perform in-system programming of serial configuration devices through the
AS programming interface. During in-system programming, the download cable
disables device access to the AS interface by driving the nCE pin high. Cyclone IV
devices are also held in reset by a low level on nCONFIG. After programming is
complete, the download cable releases nCE and nCONFIG, allowing the pull-down
and pull-up resistors to drive V
To perform in-system programming of a serial configuration device through the AS
programming interface, you must place the diodes and capacitors as close as possible
to the Cyclone IV device. You must ensure that the diodes and capacitors maintain a
maximum AC voltage of 4.1 V
If you want to use the setup shown in
of a serial configuration device and single- or multi-device AS configuration, you do
not require a series resistor on the DATA line at the near end of the serial configuration
device. The existing diodes and capacitors are sufficient.
Altera has developed the Serial FlashLoader (SFL), a JTAG-based in-system
programming solution for Altera serial configuration devices. The SFL is a bridge
design for the Cyclone IV device that uses its JTAG interface to access the EPCS JIC
(JTAG Indirect Configuration Device Programming) file and then uses the AS
interface to program the EPCS device. Both the JTAG interface and AS interface are
bridged together inside the SFL design.
For more information about implementing the SFL with Cyclone IV devices, refer to
AN 370: Using the Serial FlashLoader with the Quartus II
For more information about the USB-Blaster download cable, refer to the
Download Cable User
cable, refer to the
ByteBlaster II Download Cable User
Guide. For more information about the ByteBlaster II download
Chapter 8: Configuration and Remote System Upgrades in Cyclone IV Devices
(Figure
CC
and GND, respectively.
Figure 8–6
8–6).
to perform in-system programming
Guide.
Software.
© December 2010 Altera Corporation
USB-Blaster
Configuration
Related parts for EP4CGX150CF23I7
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
CYCLONE II STARTER KIT EP2C20N
Manufacturer:
Altera
Datasheet:
Part Number:
Description:
CPLD, EP610 Family, ECMOS Process, 300 Gates, 16 Macro Cells, 16 Reg., 16 User I/Os, 5V Supply, 35 Speed Grade, 24DIP
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
CPLD, EP610 Family, ECMOS Process, 300 Gates, 16 Macro Cells, 16 Reg., 16 User I/Os, 5V Supply, 15 Speed Grade, 24DIP
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
CPLD, EP610 Family, ECMOS Process, 300 Gates, 16 Macro Cells, 16 Reg., 16 User I/Os, 5V Supply, 30 Speed Grade, 24DIP
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
High-performance, low-power erasable programmable logic devices with 8 macrocells, 10ns
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
High-performance, low-power erasable programmable logic devices with 8 macrocells, 7ns
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
Classic EPLD
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
High-performance, low-power erasable programmable logic devices with 8 macrocells, 10ns
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Altera Corporation
Datasheet:
Part Number:
Description:
CPLD, EP610 Family, ECMOS Process, 300 Gates, 16 Macro Cells, 16 Reg., 16 User I/Os, 5V Supply, 25 Speed Grade, 24DIP
Manufacturer:
Altera Corporation
Datasheet: