EP2C20F256C6N Altera, EP2C20F256C6N Datasheet - Page 69

• Manufacturer Part Number: EP2C20F256C6N
• Description: IC CYCLONE II FPGA 20K 256-FBGA
• Manufacturer: Altera
• Series: Cyclone® IIr

Specifications of EP2C20F256C6N

• Number Of Logic Elements/cells: 18752
• Number Of Labs/clbs: 1172
• Total Ram Bits: 239616
• Number Of I /o: 152
• Voltage - Supply: 1.15 V ~ 1.25 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 256-FBGA
• For Use With: P0528 - BOARD DEV DE1 ALTERA544-1736 - CYCLONE II STARTER KIT EP2C20N
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -
• Other names: 544-1660

Altera Corporation
February 2007
I/O Banks
The I/O pins on Cyclone II devices are grouped together into I/O banks
and each bank has a separate power bus. EP2C5 and EP2C8 devices have
four I/O banks (see
EP2C50, and EP2C70 devices have eight I/O banks (see
Each device I/O pin is associated with one I/O bank. To accommodate
voltage-referenced I/O standards, each Cyclone II I/O bank has a VREF
bus. Each bank in EP2C5, EP2C8, EP2C15, EP2C20, EP2C35, and EP2C50
devices supports two VREF pins and each bank of EP2C70 supports four
VREF pins. When using the VREF pins, each VREF pin must be properly
connected to the appropriate voltage level. In the event these pins are not
used as VREF pins, they may be used as regular I/O pins.
The top and bottom I/O banks (banks 2 and 4 in EP2C5 and EP2C8
devices and banks 3, 4, 7, and 8 in EP2C15, EP2C20, EP2C35, EP2C50, and
EP2C70 devices) support all I/O standards listed in
PCI/PCI-X I/O standards. The left and right side I/O banks (banks 1 and
3 in EP2C5 and EP2C8 devices and banks 1, 2, 5, and 6 in EP2C15, EP2C20,
EP2C35, EP2C50, and EP2C70 devices) support I/O standards listed in
Table
I/O standards. See
standards.
The top and bottom I/O banks (banks 2 and 4 in EP2C5 and EP2C8
devices and banks 3, 4, 7, and 8 in EP2C15, EP2C20, EP2C35, EP2C50, and
EP2C70 devices) support DDR2 memory up to 167 MHz/333 Mbps and
QDR memory up to 167 MHz/668 Mbps. The left and right side I/O
banks (1 and 3 of EP2C5 and EP2C8 devices and 1, 2, 5, and 6 of EP2C15,
EP2C20, EP2C35, EP2C50, and EP2C70 devices) only support SDR and
DDR SDRAM interfaces. All the I/O banks of the Cyclone II devices
support SDR memory up to 167 MHz/167 Mbps and DDR memory up to
167 MHz/333 Mbps.
1
2–17, except SSTL-18 class II, HSTL-18 class II, and HSTL-15 class II
DDR2 and QDRII interfaces may be implemented in Cyclone II
side banks if the use of class I I/O standard is acceptable.
Table 2–17
Figure
2–28), while EP2C15, EP2C20, EP2C35,
for a complete list of supported I/O
Cyclone II Device Handbook, Volume 1
Cyclone II Architecture
Table
Figure
2–17, except the
2–29).
2–57