MT29F1G08ABADAH4:D Micron Technology Inc, MT29F1G08ABADAH4:D Datasheet - Page 45

• Manufacturer Part Number: MT29F1G08ABADAH4:D
• Description: MICMT29F1G08ABADAH4:D 1GB SLC NAND BGA
• Manufacturer: Micron Technology Inc

Specifications of MT29F1G08ABADAH4:D

• Cell Type: NAND
• Density: 8Gb
• Interface Type: Parallel
• Address Bus: 27b
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: 0C to 70C
• Package Type: VFBGA
• Sync/async: Asynchronous
• Operating Temperature Classification: Commercial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8b
• Number Of Words: 128M
• Supply Current: 35mA
• Mounting: Surface Mount
• Pin Count: 63
• Lead Free Status / Rohs Status: Supplier Unconfirmed

Status Operations
Table 14: Status Register Definition
PDF: 09005aef83e5ffed
m68a.pdf – Rev. D 06/10 EN
SR Bit
7
6
5
4
3
2
1
0
Program Page
Write protect
Reserved
ARDY
RDY
FAIL
–
–
–
Notes:
Program Page
Each die (LUN) provides its status independently of other die (LUNs) on the same tar-
get through its 8-bit status register.
After the READ STATUS (70h) command is issued, status register output is enabled. The
contents of the status register are returned on I/O[7:0] for each data output request.
When the asynchronous interface is active and status register output is enabled,
changes in the status register are seen on I/O[7:0] as long as CE# and RE# are LOW; it is
not necessary to toggle RE# to see the status register update.
While monitoring the status register to determine when a data transfer from the Flash
array to the data register (
command to disable the status register and enable data output (see Read Operations).
With internal ECC enabled, a READ STATUS command is required after completion of
the data transfer (
Cache Mode
Write protect
FAILC (N - 1)
RDY
1. Status register bit 6 is 1 when the cache is ready to accept new data. R/B# follows bit 6.
2. Status register bit 5 is 0 during the actual programming operation. If cache mode is
3. A status register bit defined as Rewrite Recommended signifies that the page includes
4. A status register bit defined as FAIL signifies that an uncorrectable READ error has occur-
FAIL (N)
ARDY
used, this bit will be 1 when all internal operations are complete.
acertain number of READ errors per sector (512B (main) + 4B (spare) + 8B (parity). A re-
writeof this page is recommended. (Up to a 4-bit error has been corrected if internal
ECC was enabled.)
red.
1
–
–
–
cache
2
recommended
Write protect
t
Page Read
R_ECC) to determine whether an uncorrectable read error occurred.
Reserved
Rewrite
ARDY
FAIL
RDY
–
–
4
t
R) is complete, the host must issue the READ MODE (00h)
45
3
Cache Mode
Write protect
Page Read
RDY
ARDY
1
–
–
–
–
–
Micron Technology, Inc. reserves the right to change products or specifications without notice.
cache
2
1Gb x8, x16: NAND Flash Memory
Write protect 0 = Protected
Block Erase
ARDY
RDY
FAIL
–
–
–
–
1 = Not protected
0 = Busy
1 = Ready
Don't Care
Don't Care
0 = Normal or uncorrectable
1 = Rewrite recommended
Don't Care
Don't Care
0 = Successful PROGRAM/
ERASE/READ
1 = Error in PROGRAM/
ERASE
READ
© 2010 Micron Technology, Inc. All rights reserved.
Status Operations
Description