AD7734BRUZ Analog Devices Inc, AD7734BRUZ Datasheet - Page 6

• Manufacturer Part Number: AD7734BRUZ
• Description: IC ADC 24BIT 4-CH 28-TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD7734BRUZ

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Bits: 24
• Sampling Rate (per Second): 15.4k
• Number Of Converters: 1
• Power Dissipation (max): 100mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: 28-TSSOP (0.173", 4.40mm Width)
• Resolution (bits): 24bit
• Sampling Rate: 15.4kSPS
• Input Channel Type: Single Ended
• Supply Voltage Range - Analog: 4.75V To 5.25V
• Supply Current: 13.5µA
• Number Of Elements: 1
• Resolution: 24Bit
• Architecture: Delta-Sigma
• Sample Rate: 3.05MSPS
• Input Polarity: Unipolar/Bipolar
• Input Type: Voltage
• Rated Input Volt: 5/10/±5/±10V
• Differential Input: No
• Power Supply Requirement: Analog and Digital
• Single Supply Voltage (typ): 5V
• Single Supply Voltage (min): 4.75V
• Single Supply Voltage (max): 5.25V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Power Dissipation: 100mW
• Integral Nonlinearity Error: ±0.0045%FSR
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Package Type: TSSOP
• Input Signal Type: Single-Ended
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7734EBZ - BOARD EVALUATION FOR AD7734
• Lead Free Status / Rohs Status: Compliant

AD7734
TIMING SPECIFICATIONS
Table 2. (AV
unless otherwise noted.)
Parameter
Master Clock Range
Read Operation
Write Operation
1
2
3
4
These numbers are measured with the load circuit of Figure 4 and defined as the time required for the output to cross the V
Sample tested during initial release to ensure compliance. All input signals are specified with tr = tf = 5 ns (10% to 90% of DV
1.6 V. See Figure 2 and Figure 3.
This specification is relevant only if CS goes low while SCLK is low.
These numbers are derived from the measured time taken by the data output to change 0.5 V when loaded with the circuit of Figure 4. The measured number is then
extrapolated back to remove effects of charging or discharging the 50 pF capacitor. This means that the times quoted in the Timing Characteristics are the true bus
relinquish times of the part and as such are independent of external bus loading capacitances.
t
t
t
t
t
t
t
t
t
t
t
t
t
t
t
1
2
4
5
5A
6
7
8
9
11
12
13
14
15
16
2
4
2, 3
DD
= 5 V ± 5%; DV
1
Min
1
50
500
0
0
0
0
0
50
50
0
10
0
30
25
50
50
0
DD
= 2.7 V to 3.6 V, or 5 V ± 5%; Input Logic 0 = 0 V; Logic 1 = DV
Typ
Max
6.144
60
80
60
80
80
Unit
MHz
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Rev. 0 | Page 6 of 32
Test Conditions/Comments
SYNC Pulsewidth
RESET Pulsewidth
CS Falling Edge to SCLK Falling Edge Setup Time
SCLK Falling Edge to Data Valid Delay
DV
DV
CS Falling Edge to Data Valid Delay
DV
DV
SCLK High Pulsewidth
SCLK Low Pulsewidth
CS Rising Edge after SCLK Rising Edge Hold Time
Bus Relinquish Time after SCLK Rising Edge
CS Falling Edge to SCLK Falling Edge Setup
Data Valid to SCLK Rising Edge Setup Time
Data Valid after SCLK Rising Edge Hold Time
SCLK High Pulsewidth
SCLK Low Pulsewidth
CS Rising Edge after SCLK Rising Edge Hold Time
DD
DD
DD
DD
of 4.75 V to 5.25 V
of 2.7 V to 3.3 V
of 4.75 V to 5.25 V
of 2.7 V to 3.3 V
OL
DD
or V
) and timed from a voltage level of
DD
OH
;
limits.