AD7328BRUZ Analog Devices Inc, AD7328BRUZ Datasheet - Page 14

• Manufacturer Part Number: AD7328BRUZ
• Description: IC ADC 12BIT+ SAR 8CHAN 20TSSOP
• Manufacturer: Analog Devices Inc

Specifications of AD7328BRUZ

• Data Interface: DSP, MICROWIRE™, QSPI™, Serial, SPI™
• Design Resources: Using AD7328 in Appls with Single-Ended Industrial-Level Signals (CN0047)
• Number Of Bits: 12
• Sampling Rate (per Second): 1M
• Number Of Converters: 1
• Power Dissipation (max): 30mW
• Voltage Supply Source: Dual ±
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP (0.173", 4.40mm Width)
• Resolution (bits): 13bit
• Sampling Rate: 1MSPS
• Input Channel Type: Pseudo Differential, Single Ended
• Supply Current: 900µA
• Digital Ic Case Style: TSSOP
• No. Of Pins: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-AD7328CBZ - BOARD EVALUATION FOR AD7328
• Lead Free Status / Rohs Status: RoHS Compliant part Electrostatic Device

AD7328
Channel-to-Channel Isolation
Channel-to-channel isolation is a measure of the level of crosstalk
between any two channels. It is measured by applying a full-scale,
100 kHz sine wave signal to all unselected input channels and
determining the degree to which the signal attenuates in the
selected channel with a 50 kHz signal. Figure 14 shows the worst
case across all eight channels for the AD7328. The analog input
range is programmed to be the same on all channels.
Intermodulation Distortion
With inputs consisting of sine waves at two frequencies, fa and fb,
any active device with nonlinearities creates distortion products
at sum and difference frequencies of mfa ± nfb, where m, n = 0,
1, 2, 3, and so on. Intermodulation distortion terms are those
for which neither m nor n are equal to 0. For example, the
second-order terms include (fa + fb) and (fa − fb), whereas the
third-order terms include (2fa + fb), (2fa − fb), (fa + 2fb), and
(fa − 2fb).
The AD7328 is tested using the CCIF standard where two input
frequencies near the top end of the input bandwidth are used.
In this case, the second-order terms are usually distanced in
frequency from the original sine waves, whereas the third-order
terms are usually at a frequency close to the input frequencies.
As a result, the second- and third-order terms are specified
separately. The calculation of the intermodulation distortion is
per the THD specification, where it is the ratio of the rms sum
of the individual distortion products to the rms amplitude of
the sum of the fundamentals expressed in decibels.
Power Supply Rejection (PSR)
Variations in power supply affect the full-scale transition but not
the linearity of the converter. Power supply rejection is the
maximum change in the full-scale transition point due to a
change in power supply voltage from the nominal value (see the
Typical Performance Characteristics section).
Rev. B | Page 14 of 36
Thermal Hysteresis
Thermal hysteresis is defined as the absolute maximum change
of reference output voltage after the device is cycled through
temperature from either
or
It is expressed in ppm using the following equation:
where:
V
V
T_HYS−.
Common-Mode Rejection Ratio (CMRR)
CMRR is defined as the ratio of the power in the ADC output
at full-scale frequency, f, to the power of a 100 mV sine wave
applied to the common-mode voltage of the VIN+ and VIN−
frequency, f
where Pf is the power at frequency f in the ADC output, and Pf
is the power at frequency f
REF
REF
(25°C) is V
(T_HYS) is the maximum change of V
T_HYS+ = +25°C to T
T_HYS− = +25°C to T
CMRR (dB) = 10 log (Pf/Pf
V
HYS
(
ppm
S
, as
REF
)
=
at 25°C.
V
REF
(
25
S
MAX
MIN
in the ADC output (see Figure 17).
°
V
) C
to +25°C
REF
to +25°C
S
)
−
(
V
25
REF
°
) C
(
T
_
REF
HYS
at T_HYS+ or
)
×
10
6
S