AD73360LAR-REEL7 Analog Devices Inc, AD73360LAR-REEL7 Datasheet - Page 6

• Manufacturer Part Number: AD73360LAR-REEL7
• Description: IC ANALOG FRONT END 6CH 28-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD73360LAR-REEL7

• Number Of Channels: 6
• Rohs Status: RoHS non-compliant
• Number Of Bits: 16
• Power (watts): 80mW
• Voltage - Supply, Analog: 3V
• Voltage - Supply, Digital: 3V
• Package / Case: 28-SOIC (7.5mm Width)
• Analog Front End Type: General Purpose
• Analog Front End Category: General Purpose
• Interface Type: Serial (6-Wire)
• Sample Rate: 64KSPS
• Input Voltage Range: 0.789V
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Resolution: 16b
• Number Of Adc's: 6
• Power Supply Type: Analog/Digital
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Package Type: SOIC W
• For Use With: EVAL-AD73360LEB - BOARD EVAL FOR AD73360L
• Lead Free Status / RoHS Status: Not Compliant

AD73360L
Pin No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
Mnemonic
VINP2
VINN2
VINP1
VINN1
REFOUT
REFCAP
AVDD2
AGND2
DGND
DVDD
RESET
SCLK
MCLK
SDO
SDOFS
SDIFS
SDI
SE
AGND1
AVDD1
VINP6
VINN6
VINP5
VINN5
VINP4
VINN4
VINP3
VINN3
Function
Analog Input to the Positive Terminal of Input Channel 2.
Analog Input to the Negative Terminal of Input Channel 2.
Analog Input to the Positive Terminal of Input Channel 1.
Analog Input to the Negative Terminal of Input Channel 1.
Buffered Output of the Internal Reference, which has a nominal value of 1.2 V.
Reference Voltage for ADCs. A Bypass Capacitor to AGND2 of 0.1 µF is required for the on-chip
reference. The capacitor should be fixed to this pin. The internal reference can be overdriven by an
external reference connected to this pin if required.
Analog Power Supply Connection.
Analog Ground/Substrate Connection.
Digital Ground/Substrate Connection.
Digital Power Supply Connection.
Active Low-Reset Signal. This input resets the entire chip, resetting the control registers and clearing
the digital circuitry.
Output Serial Clock, whose rate determines the serial transfer rate to/from the AD73360L. It is used
to clock data or control information to and from the serial port (SPORT). The frequency of SCLK is
equal to the frequency of the master clock (MCLK) divided by an integer number—this integer num-
ber being the product of the external master clock rate divider and the serial clock rate divider.
Master Clock Input. MCLK is driven from an external clock signal.
Serial Data Output of the AD73360L. Both data and control information may be output on this
pin and are clocked on the positive edge of SCLK. SDO is in three-state when no information is being
transmitted and when SE is low.
Framing Signal Output for SDO Serial Transfers. The frame sync is one bit wide and it is active one
SCLK period before the first bit (MSB) of each output word. SDOFS is referenced to the positive
edge of SCLK. SDOFS is in three-state when SE is low.
Framing Signal Input for SDI Serial Transfers. The frame sync is one-bit wide and it is valid one
SCLK period before the first bit (MSB) of each input word. SDIFS is sampled on the negative edge of
SCLK and is ignored when SE is low.
Serial Data Input of the AD73360L. Both data and control information may be input on this pin and
are clocked on the negative edge of SCLK. SDI is ignored when SE is low.
SPORT Enable. Asynchronous input enable pin for the SPORT. When SE is set low by the DSP, the
output pins of the SPORT are three-stated and the input pins are ignored. SCLK is also disabled inter-
nally in order to decrease power dissipation. When SE is brought high, the control and data registers of
the SPORT are at their original values (before SE was brought low); however, the timing counters and
other internal registers are at their reset values.
Analog Ground Connection.
Analog Power Supply Connection.
Analog Input to the Positive Terminal of Input Channel 6.
Analog Input to the Negative Terminal of Input Channel 6.
Analog Input to the Positive Terminal of Input Channel 5.
Analog Input to the Negative Terminal of Input Channel 5.
Analog Input to the Positive Terminal of Input Channel 4.
Analog Input to the Negative Terminal of Input Channel 4.
Analog Input to the Positive Terminal of Input Channel 3.
Analog Input to the Negative Terminal of Input Channel 3.
PIN FUNCTION DESCRIPTIONS