AD73360LAR-REEL7 Analog Devices Inc, AD73360LAR-REEL7 Datasheet - Page 25

• Manufacturer Part Number: AD73360LAR-REEL7
• Description: IC ANALOG FRONT END 6CH 28-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD73360LAR-REEL7

• Number Of Channels: 6
• Rohs Status: RoHS non-compliant
• Number Of Bits: 16
• Power (watts): 80mW
• Voltage - Supply, Analog: 3V
• Voltage - Supply, Digital: 3V
• Package / Case: 28-SOIC (7.5mm Width)
• Analog Front End Type: General Purpose
• Analog Front End Category: General Purpose
• Interface Type: Serial (6-Wire)
• Sample Rate: 64KSPS
• Input Voltage Range: 0.789V
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Resolution: 16b
• Number Of Adc's: 6
• Power Supply Type: Analog/Digital
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Package Type: SOIC W
• For Use With: EVAL-AD73360LEB - BOARD EVAL FOR AD73360L
• Lead Free Status / RoHS Status: Not Compliant

Programming a Single AD73360L for Data Mode Operation
This section describes a typical sequence in programming a
single AD73360L to operate in normal Data Mode. It details
the control (program) words that are sent to the device to con-
figure its internal registers and shows the typical output data
received during both Program and Data Modes. The device is
connected in Frame Sync Loop-Back Mode (see Figure 12),
which forces an input word from the DSP’s Tx register each time
the AD73360L outputs a word via the SDO/SDOFS lines (while
the AD73360L is in Program Mode the data transmitted will be
invalid ADC data and will, in fact, be a modified version of the
last control word written in by the DSP). In each case the DSP’s
Tx register is preloaded with the data before the frame pulse is
received. In Step 1, the part has just been reset and on the first
output event the AD73360L presents an invalid output word .
The DSP’s Tx register contains a control word that programs
CRB with the data byte 0x03. This sets the sample rate at
*ADC DATA RECEIVED BY THE DSP DURING THE PROGRAMMING PHASE SHOULD NOT BE CONSIDERED VALID RESULTS.
SET CHANNEL INVERSION
RECEIVE VALID ADC DATA
SET 8kHz SAMPLING
GLOBAL POWER-UP
SET CHANNEL GAINS
SET CHANNEL MODE
SET DATA MODE
STEP 1
STEP 2
STEP 3
STEP 4
STEP 5
STEP 6
STEP 7
1000 0001 0000 0011
1000 0010 0000 0001
1000 0011 1000 1111
1000 0110 0011 1111
1000 0111 0011 1111
1000 0000 0000 0001
0111 1111 1111 1111
CONTROL WORD
CONTROL WORD
CONTROL WORD
CONTROL WORD
CONTROL WORD
CONTROL WORD
CONTROL WORD
DSP Tx REG
DSP Tx REG
DSP Tx REG
DSP Tx REG
DSP Tx REG
DSP Tx REG
DSP Tx REG
APPENDIX A
0000 0000 0000 0000
1011 1111 0000 0011
1011 1010 0000 0001
1011 1011 1000 1111
1011 1111 0011 1111
1011 1111 0011 1111
1000 0000 0000 0000
ADC WORD 1*
ADC WORD 1*
ADC WORD 1*
ADC WORD 1*
ADC WORD 1*
ADC WORD 1*
ADC WORD 1
DEVICE 1
DEVICE 1
DEVICE 1
DEVICE 1
DEVICE 1
DEVICE 1
DEVICE 1
8 kHz (with a master clock of 16.384 MHz). In Step 2, the con-
trol word in the DSP’s Tx register will cause all the AD73360Ls
channels to power up. This data is received by the AD73360L
with the next frame sync pulse. An invalid ADC word is also
received at the DSP’s Rx register. Step 3 selects the settings for
each channel of the AD73360L. This set can be repeated as
necessary to program all the channels to the desired settings.
Steps 4 and 5 program the modes of each channel (i.e., single-
ended or differential mode and normal or inverted). Step 6 puts
the AD73360L into Data Mode and in Step 7 the first valid
ADC word is received.
This sequence assumes that the DSP SPORT’s Rx and Tx interrupts are enabled.
It is important to ensure there is no latency (separation) between control words in
a cascade configuration. This is especially the case when programming Control
Register B, as it contains settings for SCLK and DMCLK rates.
0000 0000 0000 0000
1011 1111 0000 0011
1011 1010 0000 0001
1011 1011 1000 1111
1011 1110 0011 1111
1011 1111 0011 1111
1000 0000 0000 0000
ADC WORD 1
DON'T CARE
DON'T CARE
DON'T CARE
DON'T CARE
DON'T CARE
DON'T CARE
DSP Rx REG
DSP Rx REG
DSP Rx REG
DSP Rx REG
DSP Rx REG
DSP Rx REG
DSP Rx REG
AD73360L