AD73360LAR-REEL Analog Devices Inc, AD73360LAR-REEL Datasheet - Page 18

• Manufacturer Part Number: AD73360LAR-REEL
• Description: IC ANALOG FRONT END 6CH 28-SOIC
• Manufacturer: Analog Devices Inc

Specifications of AD73360LAR-REEL

• Number Of Channels: 6
• Rohs Status: RoHS non-compliant
• Number Of Bits: 16
• Power (watts): 80mW
• Voltage - Supply, Analog: 3V
• Voltage - Supply, Digital: 3V
• Package / Case: 28-SOIC (7.5mm Width)
• Analog Front End Type: General Purpose
• Analog Front End Category: General Purpose
• Interface Type: Serial (6-Wire)
• Sample Rate: 64KSPS
• Input Voltage Range: 0.789V
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Resolution: 16b
• Number Of Adc's: 6
• Power Supply Type: Analog/Digital
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Package Type: SOIC W
• For Use With: EVAL-AD73360LEB - BOARD EVAL FOR AD73360L
• Lead Free Status / RoHS Status: Not Compliant

AD73360L
The second configuration (shown in Figure 12) has the DSP’s
Tx data and Rx data connected to the AD73360L’s SDI and
SDO, respectively, while the DSP’s Tx and Rx frame syncs are
connected to the AD73360L’s SDIFS and SDOFS. In this con-
figuration, referred to as directly coupled or frame sync loop-back,
the frame sync signals are connected together and the input data
to the AD73360L is forced to be synchronous with the output data
from the AD73360L. The DSP must be programmed so that
both the Tx and Rx frame syncs are inputs as the AD73360L’s
SDOFS will be input to both. This configuration guarantees
that input and output events occur simultaneously and is the
simplest configuration for operation in normal Data Mode. Note
that when programming the DSP in this configuration it is
advisable to preload the Tx register with the first control word to
be sent before the AD73360L is taken out of reset. This ensures
that this word will be transmitted to coincide with the first out-
put word from the device(s).
ADSP-21xx
ADSP-21xx
DSP
DSP
TFS
DT
SCLK
DR
RFS
TFS
DT
SCLK
DR
RFS
SDOFS
SDOFS
SDIFS
SDIFS
SCLK
SCLK
SDO
SDO
SDI
SDI
AD73360L
AD73360L
Digital Interfacing
The AD73360L is designed to easily interface to most common
DSPs. The SCLK, SDO, SDOFS, SDI, and SDIFS must be
connected to the SCLK, DR, RFS, DT, and TFS pins of the
DSP respectively. The SE pin may be controlled from a parallel
output pin or flag pin such as FL0–2 on the ADSP-21xx (or XF
on the TMS320C5x) or, where SPORT power-down is not
required, it can be permanently strapped high using a suitable
pull-up resistor. For consistent performance the SE should be
synchronized to the rising edge of MCLK using a circuit similar to
that of Figure 19. The RESET pin may be connected to the system
hardware reset structure or it may also be controlled using a
dedicated control line. In the event of tying it to the global system
reset, it is necessary to operate the device in mixed mode, which
allows a software reset, otherwise there is no convenient way of
resetting the device. Figures 11 and 12 show typical connections
to an ADSP-2181 while Figures 13 and 14 show typical connec-
tions to an ADSP-21xx and a TMS320C5x, respectively.
TMS320C5x
ADSP-21xx
DSP
DSP
TFS
DT
SCLK
DR
RFS
FL0
FL1
FSX
DX
CLKX
CLKR
DR
FSR
XF
SDOFS
SDOFS
RESET
RESET
SDIFS
SDIFS
SCLK
SCLK
SDO
SDO
SDI
SDI
SE
SE
FRONT-END
FRONT-END
AD73360L
AD73360L
ANALOG
ANALOG