ICS552R-01I IDT, Integrated Device Technology Inc, ICS552R-01I Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
ICS552R-01I
Manufacturer Part Number
ICS552R-01I
Description
IC OSC/MULT/BUFFER OCT 20-SSOP
Manufacturer
IDT, Integrated Device Technology Inc
Type
Clock Generator, Multiplexerr
Datasheet
1.ICS552R-01LNT.pdf
(11 pages)
Specifications of ICS552R-01I
Pll
Yes
Input
Clock, Crystal
Output
CMOS
Number Of Circuits
1
Ratio - Input:output
1:8
Differential - Input:output
No/No
Frequency - Max
200MHz
Divider/multiplier
No/Yes
Voltage - Supply
3 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
20-SSOP
Frequency-max
200MHz
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
552R-01I
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ICS552R-01I
Manufacturer:
ICS
Quantity:
87
IDT™ / ICS™ OSCILLATOR, MULTIPLIER, AND BUFFER WITH 8 OUTPUTS 7
ICS552-01
OSCILLATOR, MULTIPLIER, AND BUFFER WITH 8 OUTPUTS
External Components
Series Termination Resistor
Clock output traces over one inch should use series
termination. To series terminate a 50 trace (a
commonly used trace impedance), place a 33 resistor
in series with the clock line, as close to the clock output
pin as possible. The nominal impedance of the clock
output is 20 .
Decoupling Capacitors
As with any high-performance mixed-signal IC, the
ICS552-01 must be isolated from system power supply
noise to perform optimally.
Decoupling capacitors of 0.01µF must be connected
between each VDD and GND on pins 4 and 6, and 16
and 14. Other VDDs and GNDs can be connected to
these pins or directly to their respective ground planes.
Crystal Load Capacitors
The device crystal connections should include pads for
small capacitors from X1 to ground and from X2 to
ground. These capacitors are used to adjust the stray
capacitance of the board to match the nominally
required crystal load capacitance. Because load
capacitance can only be increased in this trimming
process, it is important to keep stray capacitance to a
minimum by using very short PCB traces (and no vias)
been the crystal and device. Crystal capacitors must be
connected from each of the pins X1 and X2 to ground.
The value (in pF) of these crystal caps should equal (C
-12 pF)*2. In this equation, C
in pF. Example: For a crystal with a 18 pF load
capacitance, two 12 pF capacitors should be used. For
a clock input, connect it X1/ICLK and leave X2
unconnected (floating).
L
= crystal load capacitance
L
PCB Layout Recommendations
For optimum device performance and lowest output
phase noise, the following guidelines should be
observed.
1) Each 0.01µF decoupling capacitor should be
mounted on the component side of the board as close
to the VDD pin as possible. No vias should be used
between decoupling capacitor and VDD pin. The PCB
trace to VDD pin should be kept as short as possible, as
should the PCB trace to the ground via.
2) The external crystal should be mounted just next to
the device with short traces. The X1 and X2 traces
should not be routed next to each other with minimum
spaces, instead they should be separated and away
from other traces.
3) To minimize EMI, the 33 series termination resistor
(if needed) should be placed close to the clock output.
4) An optimum layout is one with all components on the
same side of the board, minimizing vias through other
signal layers.
CLOCK MULTIPLIER AND BUFFER
ICS552-01
REV H 051310