ICS85354AK-01LFT IDT, Integrated Device Technology Inc, ICS85354AK-01LFT Datasheet
![no-image](/images/manufacturer_photos/0/3/324/idt__integrated_device_technology_inc_sml.jpg)
ICS85354AK-01LFT
Specifications of ICS85354AK-01LFT
Related parts for ICS85354AK-01LFT
ICS85354AK-01LFT Summary of contents
Page 1
G D ENERAL ESCRIPTION The ICS85354- 2:1/1:2 Multiplexer and ICS a member of the HiPerClockS HiPerClockS™ performance clock solutions from IDT. The 2:1 Multiplexer allows one of 2 inputs to be selected onto one output pin and the ...
Page 2
OST US DAPTER OARDS FOR Host Adapter Board Protocol SerDes Controller PCI Bus 85354AK-01 PRELIMINARY D IFFERENTIAL OUTING ETWEEN NTERNAL AND INB nINB nQB 1 1 SELA 2 ICS85354-01 D ...
Page 3
WAPPABLE INKS TO EDUNDANT INB TX nINB SerDes Q B nQB RX Linecard 85354AK-01 PRELIMINARY D IFFERENTIAL WITCH ABRIC ARDS SELB LOOP SELA LOOP 1 ICS85354-01 ...
Page 4
ABLE IN ESCRIPTIONS ...
Page 5
BSOLUTE AXIMUM ATINGS Supply Voltage Negative Supply Voltage Inputs, V (LVPECL mode) I Inputs, V (ECL mode) I Outputs Continuous Current Surge Current Operating Temperature Range, TA -40°C to +85°C Storage ...
Page 6
T 4C. LVPECL DC C ABLE HARACTERISTICS ...
Page 7
2.375V ABLE HARACTERISTICS ...
Page 8
The spectral purity in a band at a specific offset from the fundamental compared to the power of the fundamental is called the dBc Phase Noise. This value is normally expressed using a Phase noise plot and is most often ...
Page 9
P ARAMETER LVPECL V EE -0.375V to -1.465V UTPUT OAD EST IRCUIT nQx PART 1 Qx nQy PART 2 Qy tsk(pp ART TO ART KEW 80% Clock 20% ...
Page 10
IRING THE IFFERENTIAL NPUT TO Figure 1 shows how the differential input can be wired to accept single ended levels. The reference voltage V_REF = V generated by the bias resistors R1, R2 and C1. This bias ...
Page 11
LVPECL IFFERENTIAL LOCK The IN/nIN accepts LVPECL, CML, SSTL and other differen- tial signals. Both V and V must meet the V SWING OH input requirements. Figures show interface ex- amples for the HiPerClockS IN/nIN ...
Page 12
T 3.3V LVPECL O ERMINATION FOR The clock layout topology shown below is a typical termina- tion for LVPECL outputs. The two different layouts mentioned are recommended only as guidelines. FOUT and nFOUT are low impedance follower outputs that generate ...
Page 13
T 2.5V LVPECL O ERMINATION FOR Figure 4A and Figure 4B show examples of termination for 2.5V LVPECL driver. These terminations are equivalent to ter- minating 2V. For V = 2.5V, the 2.5V ...
Page 14
This section provides information on power dissipation and junction temperature for the ICS85354-01. Equations and example calculations are also provided. 1. Power Dissipation. The total power dissipation for the ICS85354-01 is the sum of the core power plus the power ...
Page 15
Calculations and Equations. The purpose of this section is to derive the power dissipated into the load. LVPECL output driver circuit and termination are shown in Figure calculate worst case power dissipation into the load, use ...
Page 16
ABLE VS IR LOW ABLE FOR JA Multi-Layer PCB, JEDEC Standard Test Boards T C RANSISTOR OUNT The transistor count for ICS85354-01 is: 210 85354AK-01 PRELIMINARY D IFFERENTIAL R I ELIABILITY NFORMATION 16 L ...
Page 17
ACKAGE UTLINE UFFIX FOR T Reference Document: JEDEC Publication 95, MO-220 85354AK-01 PRELIMINARY D IFFERENTIAL VFQFN EAD ABLE ACKAGE IMENSIONS ...
Page 18
ABLE RDERING NFORMATION ...