PAXLPV00 Red Lion Controls, PAXLPV00 Datasheet - Page 7
PAXLPV00
Manufacturer Part Number
PAXLPV00
Description
METER PROCESS VOLT 3 1/2-DIGIT
Manufacturer
Red Lion Controls
Series
PAX®LITEr
Type
Voltmeterr
Specifications of PAXLPV00
Measuring Range
0 ~ 25 VDC
Display Style
Red Characters, Black Background
Display Type
LED
Display Face Size
3.80" L x 1.95" W (96.5 x 49.5mm)
Display Digits
3.5
Display Digits - Height
0.560" (14.22mm)
Backlight
Without
Mounting Type
Panel Mount
Termination
Screw Terminals
Voltage - Supply
85 ~ 250VAC
No. Of Digits / Alpha
3-1/2
Meter Function
DC Process
Meter Range
± 0V To ± 25V
Digit Height
14.2mm
Power Consumption
6VA
Operating Temperature Range
0°C To +60°C
Supply Voltage Ac, Min
85V
Accuracy
±0.05% %
Common Mode Rejection Ratio
100 dB
Connection Type
Cage-Clamp
Cut Out, Panel
3.62×1.77 "
Dimensions
4.2"L×3.8"W×1.95"H
Display Digit Height
0.56 "
Function
Voltage
Number Of Digits
3-1/2
Primary Type
Electronic
Range, Measurement
±25 VDC
Response Time
1 sec.
Temperature, Operating
0 to 60 °C
Voltage, Input
±25 VDC
Voltage, Supply
85 to 250 VAC
Weight
0.65 lbs.
Character Size
0.56"
Display Font Color
Red
Rohs Compliant
NA
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Lead Free Status / RoHS Status
na, Contains lead / RoHS non-compliant
Other names
RLC113
difficulty in varying the measured parameter and the confusing interaction that
occurs between span and offset adjustments. However, the PAXLPV can be
quickly and easily bench calibrated using a commercially available calibrator.
CALIBRATION PROCEDURE
interaction and simplifies calibration. In Steps 1 to 4 the unit is “nulled” to zero
readout with zero input signal voltage. In Steps 5 and 6, the span adjustments
are made to establish the required slope of the transfer curve. Then in Step 7, the
transfer curve is shifted up or down as required by setting the offset adjustments.
In Step 8, the final “tweaking” adjustments are made at minimum and maximum
signal voltage. Setting the decimal points in Step 9 completes the calibration.
Before calibrating, the READOUT SPAN (Rs), SWING VOLTAGE (Vs), and
SPAN PER VOLT (Rs/Vs) must be determined.
CALIBRATION STEPS
5.0 C
Direct calibration in the signal loop is usually not practical due to the
The procedure outlined in the calibration steps below, minimizes span/offset
1. Power down the meter and remove it from its case. Turn off all offset and
2. Turn the span control pot. fully counter-clockwise (20 turns max.).
3. Turn on a combination of span adjust switches (6-10) to obtain a total value
4. Place unit in its case and apply power. Apply zero volts. Adjust the
5. Apply the SWING VOLTAGE (Vs) (4 V in this example) to the input. Set
6. Apply zero volts to see if the zero value has shifted. If it has, re-zero with the
7. After the span has been adjusted, set the signal voltage to the minimum level
span adjustment switches (S2-S10 down). S1 has no effect when zeroing
and can be in either position.
closest to (but not greater than) the SPAN PER VOLT desired (250 in this
example). The following chart gives an approximate span adjustment
value for each switch:
indicator to read zero using the offset adjustment pot.
the exact READOUT SPAN value (1000) with span adj. pot.
offset pot, then repeat Step 5.
(1 V in the example). Record the meter reading (in this example the reading
will be 250). Subtract the desired reading at minimum voltage value (0 in
the example) from the recorded reading (0-250 = - 250). Power down the
meter and remove it from its case. Set the offset add/subtract switch S1
SWITCH NUMBER
ALIBRATING THE
10
6
7
8
9
The Company warrants the products it manufactures against defects in materials and workmanship for a period limited
to two years from the date of shipment, provided the products have been stored, handled, installed, and used under proper
conditions. The Company’s liability under this limited warranty shall extend only to the repair or replacement of a
defective product, at The Company’s option. The Company disclaims all liability for any affirmation, promise or
representation with respect to the products.
The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against damages, claims,
and expenses arising out of subsequent sales of RLC products or products containing components manufactured by RLC
and based upon personal injuries, deaths, property damage, lost profits, and other matters which Buyer, its employees,
or sub-contractors are or may be to any extent liable, including without limitation penalties imposed by the Consumer
Product Safety Act (P.L. 92-573) and liability imposed upon any person pursuant to the Magnuson-Moss Warranty Act
(P.L. 93-637), as now in effect or as amended hereafter.
No warranties expressed or implied are created with respect to The Company’s products except those expressly
contained herein. The Customer acknowledges the disclaimers and limitations contained herein and relies on no other
warranties or affirmations.
SPAN VALUE
550
275
140
75
40
LIMITED WARRANTY
M
ETER
7
WHERE:
Example:
TROUBLESHOOTING
numbers listed.
Rs = (Max. Numerical Display) - (Min. Numerical Display)
Vs = (Voltage @ Max. Display) - (Voltage @ Min. Display)
Rs/Vs = READOUT SPAN (Rs)
Readout is to be 0.00 @ 1 V and 10.00 @ 5 V.
READOUT SPAN (Rs) = 1000 - 0 = 1000
SWING VOLTAGE (Vs) = 5 V - 1 V = 4 V
SPAN PER VOLT (Rs/Vs) = 1000 / 4 V = 250
8. Adjust the input signal voltage to its maximum value to see if the proper
9. Set decimal points as desired using the three decimal point switches. The
For further assistance, contact technical support at the appropriate company
(subtract = on), and the offset switches (S2-S5) to obtain a total value
closest to (but no more than) the difference between the desired reading at
minimum voltage value and the observed reading. The following chart
gives an approximate offset adjustment value for each switch:
Place the meter in its case and apply power. Using the offset adjust pot,
adjust the readout to equal the minimum voltage value (0 in the example).
readout is obtained (1000 @ 5 V in the example). If the readout is slightly
off, adjust the span pot to obtain the true reading. Then, recheck the reading
at the minimum input voltage (1 V) and readjust the offset pot if necessary.
Repeat the maximum and minimum readout adjustments until the unit
displays the proper readout at both extremes.
unit can now be installed.
SWING VOLTAGE (Vs)
SWITCH NUMBER
2
3
4
5
OFFSET VALUE
1400
700
350
175
(Disregard Decimal Points)