CUB7CCR0 Red Lion Controls, CUB7CCR0 Datasheet - Page 6
![COUNTER 8-DIGIT LV RED BACKLIGHT](/photos/21/40/214023/4242637_sml.jpg)
CUB7CCR0
Manufacturer Part Number
CUB7CCR0
Description
COUNTER 8-DIGIT LV RED BACKLIGHT
Manufacturer
Red Lion Controls
Type
High Speed Counterr
Datasheet
1.CUB7CCS0.pdf
(8 pages)
Specifications of CUB7CCR0
Count Rate
10kHz
Number Of Digits/alpha
8
Input Type
Voltage
Voltage - Supply
None Required (Battery Included)
Display Type
LCD Red Backlight
No. Of Digits / Alpha
8
Digit Height
8.9mm
Counting Speed
10kHz
Operating Temperature Range
0°C To +50°C
Signal Input Type
Contact
Display Mode
LCD Positive Reflective
Character Size
0.35"
Application
Miniature Counter
Brand/series
CUB7
Dimensions
1.10 × 2.00 × 1.64 In.
Display Digit Height
8/0.35" High
Mounting Type
Panel
Number Of Digits
8
Primary Type
Counter
Signal, Input
1.5 VDC or 50-250 VDC/VAC
Termination
Wire or Optional Plug-In Terminal
Voltage, Supply
Internal 3.6 VDC Battery
Backlighting Color
Red
Rohs Compliant
Yes
Backlight Power
9-28VDC
Counter Supply Voltage
9-28VDC
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
USING THE OPTIONAL TERMINAL BLOCK
1. Remove the rear cover. Refer to Figure 1. A small slotted screwdriver is
2. For safety concerns, the wires should be cut off completely flush with the PC
3. Break out the break away tab(s) as required. Remove the left tab only for 3
4. Reinstall the rear cover into CUB7 unit.
5. Mount the CUB7 into the panel (refer to 1.0 Installing The Meter)
6. Push the keyed terminal block onto the exposed PC board. The left most
Note: Wire sizes 16-24 AWG may be used with 0.25" length exposed. The
Current Sinking Output
Switch/Contact Sinking Output
required to release the side latches. Insert the screwdriver tip between the
rear cover and the side of the unit. Leverage the screwdriver away from the
case to unlatch the side latch and slightly lift the rear cover. Pinch the
corners to hold the rear cover in place. Remove the screwdriver and repeat
the same procedure on the other side of the rear cover. When both side
latches are released, slide the rear cover from the unit and the wires.
board to prevent a short.
position terminal block or both tabs for 4 and 5 position terminal blocks.
terminal, next to the DIP switch(s) is terminal #1.
screwless type terminal block requires a small slotted screwdriver engaged in
the upper slot to open the wire clamp in the lower larger slot. Removing the
screwdriver will lock the wire clamp unto the wire.
ON
1
ON
1
2
2
*
3
Switch position is application dependent.
*
3
Wires must be cut off completely
flush with PC board.
1
1
2
2
3
3
4
4
+
−
+
−
DIP Switch(s)
Cut Wires Internally
Optional
Backlight
Power
Optional
Backlight
Power
(If using Optional
Terminal Block)
Current Sourcing Output
Switch/Contact Sourcing Output
ON
1
ON
1
2
2
3
*
*
3
Side Latches
+V
+V
Break-out Tab or Tabs
(If using Optional
1
1
Terminal Block)
2
6
2
3
3
4
4
+
−
+
−
Latches
Backlight
Power
Optional
Optional
Backlight
Power
Side
Rear Cover
Shaded area for high voltage applications.
Figure 1
Logic Output
ON
High Voltage
ON
1
3
*
2
*
3
VDC/VAC
50-250
Open & Lock
Mounting Clip
Wire Clamp
1
1
2
2
3
3
4
4
5
Terminal #1
+
−
Optional
Terminal Block
+
−
Optional
Backlight
Power
Optional
Backlight
Power