CUB5R000 Red Lion Controls, CUB5R000 Datasheet - Page 6

• Manufacturer Part Number: CUB5R000
• Description: COUNTER/RATE IND DUAL REFL DISPL
• Manufacturer: Red Lion Controls
• Series: CUB5r
• Type: Counter/Rate Indicatorr

Specifications of CUB5R000

• Count Rate: 20kHz
• Number Of Digits/alpha: 8
• Input Type: Voltage, Switch Closure, Transistor Switch
• Voltage - Supply: 9 V ~ 28 V
• Display Type: LCD Non-Backlit
• No. Of Digits / Alpha: 8
• Digit Height: 11.7mm
• Counting Speed: 20kHz
• Operating Temperature Range: -35°C To +75°C
• Signal Input Type: Current
• Character Size: 0.46"
• Ip/nema Rating: IP65 / NEMA 4X
• Accuracy: ±0.01% %
• Connection Type: Screw
• Counter Type: Up⁄Down & Rate
• Cut Out, Panel: 2.68×1.3 "
• Dimensions: 2.95"L×1.86"W×1.54"H
• Display Digit Height: 0.46 "
• Display Range: -9999999 to [phone]
• Frequency, Operating: 20 kHz (Max.)
• Function: Counter/Rate Indicator
• Material, Casing: Plastic
• Memory Type: EEPROM
• Mounting Type: Panel
• Number Of Digits: 8
• Output Type: Relay
• Primary Type: Electronic
• Range, Measurement: -9999999 to 999999
• Special Features: Programmable
• Standards: CE Marked
• Temperature, Operating, Range: -35 to +75 °C
• Terminal Type: Screw Terminal
• Termination: Screw Terminal
• Voltage, Supply: 9 to 28 VDC
• Weight: 3.2 Oz.
• Memory: Nonvolatile EEPROM
• User Input: Programmable, Connect to Common to Activate Function
• Rate Minimum Input Frequency: 0.01 Hz
• Rate Maximum Frequency: 20 kHz
• Operating Temperature: 0 to 60°C
• Panel Cutout: 2.68" × 1.30"
• Counter Supply Voltage: 9-28VDC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Output Type: -
• Lead Free Status / Rohs Status: RoHS Compliant part
• Other names: RLC121

OPERATING MODE DISPLAY DESIGNATORS
the rate and count values.
PROGRAMMING MODE ENTRY (SEL KEY)
installation. The meter normally operates in the Display Mode. No parameters
can be programmed in this mode. The Programming Mode is entered by
pressing and holding the
either a security code, or a hardware lock.
MODULE ENTRY (SEL & RST KEYS)
group together parameters that are related in function. The display will alternate
between
module. The displayed module is entered by pressing the
MODULE MENU (SEL KEY)
module discussion). The
to be changed, without changing the programming of preceding parameters.
After completing a module, the display will return to
continue by accessing additional modules.
SELECTION / VALUE ENTRY
the selections/value for that parameter. The
selections/values for that parameter. Pressing the
displayed selection/value. This also advances the meter to the next parameter.
most digit will begin to flash. Pressing the
by one or the user can hold the
The
will enter the value and move to the next parameter.
5.0 R
6.0 P
“
Pressing the
It is recommended all programming changes be made off line, or before
The Programming Menu is organized into separate modules. These modules
Each module has a separate module menu (which is shown at the start of each
For each parameter, the display alternates between the present parameter and
For numeric values, press the
R
SEL
”
- To the left of the display is the rate value.
- Counter A has no designator.
Pro
key will advance to the next digit. Pressing and holding the
KEY
SEL
RST
and the present module. The
SEL
DISPLAY
ROGRAMMING THE
SEL
button toggles the meter through the selected displays. If display scroll is enabled, the display will toggle automatically every four seconds between
EVIEWING THE
DISPLAY MODE OPERATION
Index display through enabled values
Resets count display(s) and/or outputs
MODE
Pro
NO
SEL
SEL
key is pressed to advance to a particular parameter
key. If it is not accessible then it is locked by
RST
RST
Input Setup
1-INPUt
Parameters
RST
key and the digit will automatically scroll.
key to access the value. The right hand
RST
RST
SEL
RST
key is used to select the desired
SEL
key is used to move through the
key again increments the digit
key, stores and activates the
Pro NO
SEL
. Programming may
Parameters
key.
Rate Setup
2-rAtE
PROGRAMMING MENU
ENTERING PROGRAM MODE
Press and hold for 2 seconds to activate
F
SEL
SEL
OVERVIEW
RONT
SEL
key
M
6
Display and Front
ETER
3-dSPLAY
Parameters
PROGRAMMING MODE EXIT (SEL KEY)
displayed. This will commit any stored parameter changes to memory and
return the meter to the Display Mode. (If power loss occurs before returning to
the Display Mode, verify recent parameter changes.)
PROGRAMMING TIPS
When programming is complete, it is recommended to record the parameter
programming and lock out parameter programming with the user input or
programming security code.
FACTORY SETTINGS
encountering programming problems.
ALTERNATING SELECTION DISPLAY
appear. This is used to illustrate the display alternating between the parameter
on top and the parameter’s factory setting on the bottom. In most cases,
selections and values for the parameter will be listed on the right.
Panel Key
“
“1” and “2” - Indicates setpoint 1 and 2 output status.
The Programming Mode is exited by pressing the
It is recommended to start with Module 1 for counting or Module 2 for rate.
Factory settings may be completely restored in Module 3. This is useful when
In the explanation of the modules, the following dual display with arrows will
B
b
”
- To the left of the display is the Counter B value (dual count or batch).
SEL
RST
UTTONS AND
Parameter
Indicates Program Mode Alternating Display
PROGRAMMING MODE OPERATION
Store selected parameter and index to next parameter
Advances through the program menu/
Increments selected parameter value or selection
Parameters
4-SEtPt
Setpoint

INP A-b
Output
Factory Settings are shown.
SEL
Cnt ud

Parameters
D
5-SEriAL
Selection/Value
Setup
Serial
ISPLAY
SEL
SEL
key with
Pro NO