HMMC-1002 Avago Technologies US Inc., HMMC-1002 Datasheet
HMMC-1002
Specifications of HMMC-1002
Related parts for HMMC-1002
HMMC-1002 Summary of contents
Page 1
... FETs and four 200 mm wide shunt FETs. The distributed topology of the HMMC- 1002 minimizes the parasitic effects of its series and shunt FETs, allowing the HMMC-1002 to exhibit a wide dynamic range across its full bandwidth. An on- chip DC reference circuit may be used to maintain ...
Page 2
... T Max. Ambient Operating Temp. maxa T Storage Temperature stg T Max. Assembly Temp. (for 60 sec. max.) max Notes: 1. Operation in excess of any one of these conditions may result in damage to this device. HMMC-1002 DC Specifications/Physical Properties, T Symbol Parameters and Test Conditions I V Control Current -4V Control Current, (V ...
Page 3
... Application The HMMC-1002 is designed to be used as a gain con- trol block in an ALC assembly. Because of its wide dynamic range and return loss performance, the HMMC-1002 may also be used as a broadband pulse modulator or single-pole single-throw, non-reflective switch. Operation The attenuation value of the HMMC-1002 is adjusted ...
Page 4
... All dimensions in microns and shown to center of bond pad V1 and V bonding pads are microns. in out input and output bonding pads are microns. 4. Chip thickness: 127 ± 15 µm. Figure 2. HMMC-1002 Bonding Pad Locations Wire Bonds using 0.7 mil dia. Gold Bond Wire (Length NOT important Figure 3. HMMC-1002 Assembly Diagram. 4 ...
Page 5
... 500Ω V REF (-0 -1.0 V) 500Ω (350Ω – 500Ω) Figure 4. Attenuator Driver. HMMC-1002 Typical Performance 1.5 4.0 8.0 12.0 16.0 20.0 24.0 26.5 FREQUENCY (GHz) [1] Figure 5. Attenuation vs. Frequency . Note: 1. Data obtained from on-wafer measurements Op. Amp – REF 0 Maximum Attenuation ...
Page 6
... HMMC-1002 Typical Power Performance All Attenuation Settings were done at 1 GHz INPUT POWER (dBm) Figure 7. Attenuation vs. Input Power [1] @ 50.0 MHz INPUT POWER (dBm) Figure 10. Attenuation vs. Input Power [1] @ 14.0 GHz. . Note: 1. Data taken with the device mounted in connectorized package INPUT POWER (dBm) Figure 8 ...
Page 7
... HMMC-1002 Typical Harmonic Performance -20 Fundamental Frequency: -30 50 MHz 10 GHz -40 2 GHz -50 -60 -70 -80 - ATTENUATION (dB) Figure 13. Second Harmonic Suppression vs. [1] Attenuation. Input Power = 0 dBm . Note: 1. Data taken with the device mounted in connectorized package. 7 -20 Fundamental Frequency: -30 50 MHz 2 GHz -40 -50 -60 -70 -80 -90 ...
Page 8
... HMMC-1002 Typical Temperature Performance FREQUENCY (GHz) Figure 15. Attenuation vs. Temperature @ [1] Minimum Attenuation FREQUENCY (GHz) Figure 18. Attenuation vs. Temperature [ Attenuation. . Note: 1. Data taken with the device mounted in connectorized package. This data sheet contains a variety of typical and guaranteed performance data. The information supplied should not be interpreted as a complete list of circuit specifications. In this data sheet the term typical refers to the 50th percentile performance. For additional information contact your local Avago Technologies’ ...