DP83815DVNG/HAPB National Semiconductor, DP83815DVNG/HAPB Datasheet - Page 6

• Manufacturer Part Number: DP83815DVNG/HAPB
• Manufacturer: National Semiconductor

Specifications of DP83815DVNG/HAPB

• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (min): 3V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 144
• Lead Free Status / RoHS Status: Not Compliant

2.0 Pin Description
PCI Bus Interface
AD[31-0]
CBEN[3-0]
PCICLK
DEVSELN
FRAMEN
GNTN
IDSEL
INTAN
IRDYN
PAR
Symbol
66, 67, 68, 70,
71, 72, 73, 74,
78, 79, 81, 82,
83, 86, 87, 88,
101, 102, 104,
105, 106, 108,
109, 110, 112,
118, 119, 120,
113, 115, 116,
75, 89, 100,
LQFP Pin
No(s)
121
111
60
95
91
63
76
61
92
99
K11, J13, J14,
P7, N10, L10,
N4, L7, M10,
N5, M5, L5,
K3, K2, K4,
L3, L2, M1,
N6, L6, N7,
N3, P3, L4
M13, M14,
LBGA Pin
M11, N11,
P12, N12,
K13, K14,
L12, L14,
No(s)
P10
L13
J12
M7
M4
H4
P9
P8
J2
J1
Dir
I/O
I/O
I/O
I/O
I/O
I/O
O
I
I
I
Address and Data: Multiplexed address and data bus. As a bus
master, the DP83815 will drive address during the first bus phase.
During subsequent phases, the DP83815 will either read or write
data expecting the target to increment its address pointer. As a bus
target, the DP83815 will decode each address on the bus and
respond if it is the target being addressed.
Bus Command/Byte Enable: During the address phase these
signals define the “bus command” or the type of bus transaction that
will take place. During the data phase these pins indicate which byte
lanes contain valid data. CBEN[0] applies to byte 0 (bits 7-0) and
CBEN[3] applies to byte 3 (bits 31-24) in the Little Endian Mode. In
Big Endian Mode, CBEN[3] applies to byte 0 (bits 31-24) and
CBEN[0] applies to byte 3 (bits 7-0).
Clock: This PCI Bus clock provides timing for all bus phases. The
rising edge defines the start of each phase. The clock frequency
ranges from 0 to 33 MHz.
Device Select: As a bus master, the DP83815 samples this signal to
insure that the destination address for the data transfer is recognized
by a PCI target. As a target, the DP83815 asserts this signal low
when it recognizes its address after FRAMEN is asserted.
Frame: As a bus master, this signal is asserted low to indicate the
beginning and duration of a bus transaction. Data transfer takes
place when this signal is asserted. It is de-asserted before the
transaction is in its final phase. As a target, the device monitors this
signal before decoding the address to check if the current transaction
is addressed to it.
Grant: This signal is asserted low to indicate to the DP83815 that it
has been granted ownership of the bus by the central arbiter. This
input is used when the DP83815 is acting as a bus master.
Initialization Device Select: This pin is sampled by the DP83815 to
identify when configuration read and write accesses are intended for
it.
Interrupt A: This signal is asserted low when an interrupt condition
occurs as defined in the Interrupt Status Register, Interrupt Mask,
and Interrupt Enable registers.
Initiator Ready: As a bus master, this signal will be asserted low
when the DP83815 is ready to complete the current data phase
transaction. This signal is used in conjunction with the TRYDN
signal. Data transaction takes place at the rising edge of PCICLK
when both IRDYN and TRDYN are asserted low. As a target, this
signal indicates that the master has put the data on the bus.
Parity: This signal indicates even parity across AD[31-0] and
CBEN[3-0] including the PAR pin. As a master, PAR is asserted
during address and write data phases. As a target, PAR is asserted
during read data phases.
6
Description
www.national.com