S29GL064N90BFI040 Spansion Inc., S29GL064N90BFI040 Datasheet - Page 53
![no-image](/images/manufacturer_photos/0/6/621/spansion_inc__sml.jpg)
S29GL064N90BFI040
Manufacturer Part Number
S29GL064N90BFI040
Description
Manufacturer
Spansion Inc.
Datasheet
1.S29GL064N90BFI040.pdf
(81 pages)
Specifications of S29GL064N90BFI040
Cell Type
NOR
Density
64Mb
Access Time (max)
90ns
Interface Type
Parallel
Boot Type
Bottom
Address Bus
23/22Bit
Operating Supply Voltage (typ)
3/3.3V
Operating Temp Range
-40C to 85C
Package Type
FBGA
Sync/async
Asynchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Word Size
8/16Bit
Number Of Words
8M/4M
Supply Current
50mA
Mounting
Surface Mount
Pin Count
48
Lead Free Status / RoHS Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
S29GL064N90BFI040A
Manufacturer:
INTEL
Quantity:
3 574
October 29, 2008 S29GL-N_01_12
Legend
X = Don’t care
RA = Read Address of memory location to be read.
RD = Read Data read from location RA during read operation.
PA = Program Address. Addresses latch on falling edge of WE# or CE# pulse,
whichever happens later.
Notes
1. See
2. All values are in hexadecimal.
3. Shaded cells indicate read cycles. All others are write cycles.
4. During unlock and command cycles, when lower address bits are 555 or
5. Unless otherwise noted, address bits A21–A11 are don’t cares.
6. No unlock or command cycles required when device is in read mode.
7. Reset command is required to return to read mode (or to erase-suspend-
8. Fourth cycle of autoselect command sequence is a read cycle. Data bits
9. For S29GL064N and S29GL032A Device ID must be read in three cycles.
Read
Reset
Enter Secured Silicon Sector Region
Exit Secured Silicon Sector Region
Program
Write to Buffer
Program Buffer to Flash
Write to Buffer Abort Reset
Chip Erase
Sector Erase
Unlock Bypass
Unlock Bypass Program
Unlock Bypass RESET
Program/Erase Suspend
Program/Erase Resume
CFI Query
AAA as shown in table, address bits above A11 are don’t care.
read mode if previously in Erase Suspend) when device is in autoselect
mode, or if DQ5 goes high while device is providing status information.
DQ15–DQ8 are don’t care. See
on page 42
Manufacturer ID
Device ID
Device ID
Secured Silicon Sector Factory Protect
Sector Protect Verify
(Note 11)
(Note 6)
(Note 7)
Table 8.1 on page 17
Command Sequence
(Note 16)
(Note 9)
(Note 12)
for more information.
(Note 1)
(Note 15)
(Note 14)
(Note 13)
for description of bus operations.
Autoselect Command Sequence
Table 10.3 Command Definitions (x8 Mode, BYTE# = V
4
1
1
4
6
4
4
3
4
4
3
1
3
6
6
1
1
1
Addr
XXX
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
XXX
XXX
XXX
XXX
RA
SA
AA
First
D a t a
Data
RD
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
AA
A0
B0
F0
29
90
30
98
S29GL-N MirrorBit
Addr
XXX
555
555
555
555
555
555
555
555
555
555
555
555
555
PA
S h e e t
Second
Data
PD
55
55
55
55
55
55
55
55
55
55
55
55
55
00
Addr
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
AAA
SA
®
PD = Program Data for location PA. Data latches on rising edge of WE# or
CE# pulse, whichever happens first.
SA = Sector Address of sector to be verified (in autoselect mode) or erased.
Address bits A21–A15 uniquely select any sector.
WBL = Write Buffer Location. Address must be within same write buffer page
as PA.
BC = Byte Count. Number of write buffer locations to load minus 1.
10. Refer to
11. Data is 00h for an unprotected sector and 01h for a protected sector.
12. Total number of cycles in command sequence is determined by number of
13. Command sequence resets device for next command after aborted write-
14. System may read and program in non-erasing sectors, or enter autoselect
15. Erase Resume command is valid only during Erase Suspend mode.
16. Command is valid when device is ready to read array data or when device
17. Refer to
Third
Flash Family
factory protect status.
bytes written to write buffer. Maximum number of cycles in command
sequence is 37, including Program Buffer to Flash command.
to-buffer operation.
mode, when in Erase Suspend mode. Erase Suspend command is valid
only during a sector erase operation.
is in autoselect mode.
and model number.
Data
A0
F0
90
90
90
90
90
88
90
25
80
80
20
Bus Cycles (Notes 2–5)
Table 8.9 on page
Table 8.9 on page
(SA)X04
Addr
XXX
AAA
AAA
X00
X02
X02
X06
PA
SA
Fourth
(Note 10)
00/01
Data
PD
BC
AA
AA
01
7E
00
29, for individual Device IDs per device density
29, for data indicating Secured Silicon Sector
IL
)
Addr
X1C
555
555
PA
Fifth
(Note 17)
Data
PD
55
55
Addr
WBL
AAA
X1E
SA
Sixth
(Note 17)
Data
PD
10
30
53