PIC18F87K90-E/PT Microchip Technology, PIC18F87K90-E/PT Datasheet - Page 369

• Manufacturer Part Number: PIC18F87K90-E/PT
• Description: 128kB Flash, 4kB RAM, 1kB EE, 16MIPS, NanoWatt XLP, LCD, 5V 80 TQFP 12x12x1mm TR
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F87K90-E/PT

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 69
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 24x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 80-TQFP
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

22.3.2
Once Synchronous mode is selected, reception is
enabled by setting either the Single Receive Enable bit,
SREN (RCSTAx<5>), or the Continuous Receive
Enable bit, CREN (RCSTAx<4>). Data is sampled on
the RXx pin on the falling edge of the clock.
If enable bit, SREN, is set, only a single word is
received. If enable bit, CREN, is set, the reception is
continuous until CREN is cleared. If both bits are set,
then CREN takes precedence.
To set up a Synchronous Master Reception:
1.
2.
FIGURE 22-13:
 2009-2011 Microchip Technology Inc.
RC6/TX1/CK1/
RC6/TX1/CK1/
Note:
RC7/RX1/DT1/
Initialize the SPBRGHx:SPBRGx registers for the
appropriate baud rate. Set or clear the BRG16
bit, as required, to achieve the desired baud rate.
Enable the synchronous master serial port by
setting bits, SYNC, SPEN and CSRC.
(TXCKP = 0)
(TXCKP = 1)
SEG27 Pin
SEG27 Pin
SEG28 Pin
bit, SREN
(Interrupt)
RC1IF bit
SREN bit
CREN bit
RCREG1
Write to
Timing diagram demonstrates Sync Master mode with bit, SREN = 1, and bit, BRGH = 0. This example is equally applicable to EUSART2
(RG1/TX2/CK2/AN19/C3OUT and RG2/RX2/DT2/AN18/C3INA).
Read
EUSART SYNCHRONOUS
MASTER RECEPTION
Q2
‘0’
Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
SYNCHRONOUS RECEPTION (MASTER MODE, SREN)
bit 0
Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
bit 1
bit 2
bit 3
PIC18F87K90 FAMILY
3.
4.
5.
6.
7.
8.
9.
10. If any error occurred, clear the error by clearing
11. If using interrupts, ensure that the GIE and PEIE bits
Ensure bits, CREN and SREN, are clear.
If interrupts are desired, set enable bit, RCxIE.
If 9-bit reception is desired, set bit, RX9.
If a single reception is required, set bit, SREN.
For continuous reception, set bit, CREN.
Interrupt flag bit, RCxIF, will be set when recep-
tion is complete and an interrupt will be generated
if the enable bit, RCxIE, was set.
Read the RCSTAx register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREGx register.
bit CREN.
in the INTCON register (INTCON<7:6>) are set.
bit 4
bit 5
bit 6
DS39957D-page 369
bit 7
Q1 Q2 Q3 Q4
‘0’