PIC12F635T-I/MD Microchip Technology, PIC12F635T-I/MD Datasheet - Page 34
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
PIC12F635T-I/MD
Manufacturer Part Number
PIC12F635T-I/MD
Description
1.75 KB Flash, 64 RAM, 6 I/O 8 DFN 4x4mm T/R
Manufacturer
Microchip Technology
Series
PIC® 12Fr
Specifications of PIC12F635T-I/MD
Core Processor
PIC
Core Size
8-Bit
Speed
20MHz
Peripherals
Brown-out Detect/Reset, POR, WDT
Number Of I /o
5
Program Memory Size
1.75KB (1K x 14)
Program Memory Type
FLASH
Eeprom Size
128 x 8
Ram Size
64 x 8
Voltage - Supply (vcc/vdd)
2 V ~ 5.5 V
Oscillator Type
Internal
Operating Temperature
-40°C ~ 85°C
Package / Case
8-DFN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
For Use With
AC164326 - MODULA SKT PM3 20QFNXLT08DFN2 - SOCKET TRANSITION ICE 14DIP/8DFNXLT08DFN - SOCKET TRANSITION ICE 8DFN
Data Converters
-
Connectivity
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
- Current page: 34 of 234
- Download datasheet (4Mb)
during a CALL or GOTO instruction (PCLATH<4:3>
PIC12F635/PIC16F636/639
2.3
The Program Counter (PC) is 13 bits wide. The low byte
comes from the PCL register, which is a readable and
writable register. The high byte (PC<12:8>) is not
directly readable or writable and comes from PCLATH.
On any Reset, the PC is cleared. Figure 2-5 shows the
two situations for the loading of the PC. The upper
example in Figure 2-5 shows how the PC is loaded on a
write to PCL (PCLATH<4:0>
example in Figure 2-5 shows how the PC is loaded
PCH).
FIGURE 2-5:
2.3.1
Executing any instruction with the PCL register as the
destination
Counter PC<12:8> bits (PCH) to be replaced by the
contents of the PCLATH register. This allows the entire
contents of the program counter to be changed by
writing the desired upper 5 bits to the PCLATH register.
When the lower 8 bits are written to the PCL register, all
13 bits of the program counter will change to the values
contained in the PCLATH register and those being
written to the PCL register.
A computed GOTO is accomplished by adding an offset
to the program counter (ADDWF PCL). Care should be
exercised when jumping into a look-up table or
program branch table (computed GOTO) by modifying
the PCL register. Assuming that PCLATH is set to the
table start address, if the table length is greater than
255 instructions or if the lower 8 bits of the memory
address rolls over from 0xFF to 0x00 in the middle of
the table, then PCLATH must be incremented for each
address rollover that occurs between the table
beginning and the target location within the table.
For more information refer to Application Note AN556,
“Implementing a Table Read” (DS00556).
DS41232D-page 32
PC
PC
12
12 11 10
2
PCL and PCLATH
5
PCH
PCLATH<4:3>
PCH
MODIFYING PCL
simultaneously causes the
PCLATH
PCLATH<4:0>
8
PCLATH
8
7
7
LOADING OF PC IN
DIFFERENT SITUATIONS
PCL
PCL
11
8
PCH). The lower
0
0
Instruction with
Opcode<10:0>
ALU Result
GOTO, CALL
Destination
Program
PCL as
2.3.2
The
8-level x 13-bit wide hardware stack (see Figure 2-1).
The stack space is not part of either program or data
space and the Stack Pointer is not readable or writable.
The PC is PUSHed onto the stack when a CALL
instruction is executed or an interrupt causes a branch.
The stack is POPed in the event of a RETURN, RETLW
or a RETFIE instruction execution. PCLATH is not
affected by a PUSH or POP operation.
The stack operates as a circular buffer. This means that
after the stack has been PUSHed eight times, the ninth
push overwrites the value that was stored from the first
push. The tenth push overwrites the second push (and
so on).
2.4
The INDF register is not a physical register. Addressing
the INDF register will cause indirect addressing.
Indirect addressing is possible by using the INDF
register. Any instruction using the INDF register
actually accesses data pointed to by the File Select
Register (FSR). Reading INDF itself indirectly will
produce 00h. Writing to the INDF register indirectly
results in a no operation (although Status bits may be
affected). An effective 9-bit address is obtained by
concatenating the 8-bit FSR and the IRP bit of the
STATUS register, as shown in Figure 2-6.
A simple program to clear RAM location 20h-2Fh using
indirect addressing is shown in Example 2-1.
EXAMPLE 2-1:
NEXT
CONTINUE
Note 1: There are no Status bits to indicate stack
PIC12F635/PIC16F636/639
2: There are no instructions/mnemonics
Indirect Addressing, INDF and
FSR Registers
STACK
MOVLW
MOVWF
CLRF
INCF
BTFSS
GOTO
overflow or stack underflow conditions.
called PUSH or POP. These are actions
that occur from the execution of the CALL,
RETURN, RETLW and RETFIE instructions
or the vectoring to an interrupt address.
0x20
FSR
INDF
FSR
FSR,4
NEXT
INDIRECT ADDRESSING
© 2007 Microchip Technology Inc.
;initialize pointer
;to RAM
;clear INDF register
;INC POINTER
;all done?
;no clear next
;yes continue
family
has
an
Related parts for PIC12F635T-I/MD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![PIC12F635-I/SN](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 1KX14 8SOIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC12F635-I/P](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 1KX14 8DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC12F635-I/MD](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC PIC MCU FLASH 1KX14 8DFN
Manufacturer:
Microchip Technology
Datasheet:
![PIC12F635-E/MD](/images/no-image3.png)
Part Number:
Description:
8/14-Pin, Flash-Based 8-Bit CMOS Microcontrollers with nanoWatt Technology
Manufacturer:
MICROCHIP [Microchip Technology]
Datasheet:
![PIC12F635-E/P](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 1KX14 8DIP
Manufacturer:
Microchip Technology
Datasheet:
![PIC12F635-I/MF](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 1KX14 8DFN
Manufacturer:
Microchip Technology
Datasheet:
![PIC12F635-E/MF](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC MCU FLASH 1KX14 8DFN
Manufacturer:
Microchip Technology
Datasheet:
![PIC12F635-E/SN](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,SOP,8PIN,PLASTIC
Manufacturer:
Microchip Technology
Datasheet:
![PIC12F639](/images/manufacturer_photos/0/4/439/microchip_technology_tmb.jpg)
Part Number:
Description:
(PIC12F635 / PIC12F636 / PIC12F639) 8/14-PIN FLASH-BASED / 8-BIT CMOS MICROCONTROLLERS WITH NANOWATT TECHNOLOGY
Manufacturer:
Microchip Technology
Datasheet:
![PIC12F1840-I/P](/photos/16/3/160349/pdip8_tmb.jpg)
Part Number:
Description:
7 KB Flash, 256 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core 8 PDI
Manufacturer:
Microchip Technology
Datasheet:
![PIC12LF1840-I/MF](/photos/16/0/160077/dfn8_tmb.jpg)
Part Number:
Description:
7 KB Flash, 256 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core, Nano
Manufacturer:
Microchip Technology
Datasheet:
![PIC12F1840-I/MF](/photos/16/0/160077/dfn8_tmb.jpg)
Part Number:
Description:
7 KB Flash, 256 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core 8 DFN
Manufacturer:
Microchip Technology
![PIC12F1840-I/SN](/photos/16/3/160347/soic8_tmb.jpg)
Part Number:
Description:
7 KB Flash, 256 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core 8 SOI
Manufacturer:
Microchip Technology
![PIC12LF1840-E/MF](/photos/16/0/160077/dfn8_tmb.jpg)
Part Number:
Description:
7 KB Flash, 256 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core, Nano
Manufacturer:
Microchip Technology
Datasheet:
![PIC12LF1840-E/P](/photos/16/3/160349/pdip8_tmb.jpg)
Part Number:
Description:
7 KB Flash, 256 Bytes RAM, 32 MHz Int. Osc, 6 I/0, Enhanced Mid Range Core, Nano
Manufacturer:
Microchip Technology
Datasheet: