GTL2009PW NXP Semiconductors, GTL2009PW Datasheet - Page 13
![Comparator ICs 3-BIT FSB FREQ CMPR](/photos/15/59/155965/soic16_sml.jpg)
GTL2009PW
Manufacturer Part Number
GTL2009PW
Description
Comparator ICs 3-BIT FSB FREQ CMPR
Manufacturer
NXP Semiconductors
Datasheet
1.GTL2009PW118.pdf
(17 pages)
Specifications of GTL2009PW
Number Of Channels
3 Channels
Comparator Type
Magnitude
Product
Digital Comparators
Output Type
Complementary
Supply Voltage (max)
3.6 V
Supply Voltage (min)
3 V
Supply Current (max)
10 mA
Maximum Operating Temperature
85 C
Mounting Style
SMD/SMT
Package / Case
SOT-403
Minimum Operating Temperature
- 40 C
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
GTL2009PW,112
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
GTL2009PW
Manufacturer:
PHILIPS/飞利浦
Quantity:
20 000
Philips Semiconductors
15. Soldering
9397 750 13556
Product data sheet
15.1 Introduction to soldering surface mount packages
15.2 Reflow soldering
15.3 Wave soldering
This text gives a very brief insight to a complex technology. A more in-depth account of
soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine pitch
SMDs. In these situations reflow soldering is recommended.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and cooling)
vary between 100 seconds and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 C to 270 C depending on solder paste
material. The top-surface temperature of the packages should preferably be kept:
Moisture sensitivity precautions, as indicated on packing, must be respected at all times.
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal results:
•
•
•
•
below 225 C (SnPb process) or below 245 C (Pb-free process)
– for all BGA, HTSSON..T and SSOP..T packages
– for packages with a thickness
– for packages with a thickness < 2.5 mm and a volume
below 240 C (SnPb process) or below 260 C (Pb-free process) for packages with a
thickness < 2.5 mm and a volume < 350 mm
Use a double-wave soldering method comprising a turbulent wave with high upward
pressure followed by a smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint longitudinal axis is preferred to be
thick/large packages.
parallel to the transport direction of the printed-circuit board;
Rev. 01 — 22 September 2005
3-bit GTL Front-Side Bus frequency comparator
2.5 mm
3
so called small/thin packages.
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
350 mm
GTL2009
3
so called
13 of 17