CUB5COM1 Red Lion Controls, CUB5COM1 Datasheet - Page 11
![RS485 Serial Communications Card](/photos/27/52/275234/4607896_sml.jpg)
CUB5COM1
Manufacturer Part Number
CUB5COM1
Description
RS485 Serial Communications Card
Manufacturer
Red Lion Controls
Specifications of CUB5COM1
Accessory Type
RS485 Serial Communications Card
Brand/series
CUB5COM Series
Card Type
RS485 Serial Communications
Data Rate
300 to 19.2 K
Standards
UL Listed, IEC Certified
For Use With
Red Lion CUB5 Miniature Electronic 8-Digit Dual Counters And Rate Indicators
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
SPn ASN
"
Setpoint 1 is completely programmed, the display returns to
steps for Setpoint 2 if both Setpoints are used in the application.
available is dependent on the Setpoint option module installed.
selected, the unit returns to
Output Module is installed in the meter. Some parameters in the menu will not
appear depending on the Setpoint Assignment and Setpoint Output Action. The
Setpoint Parameter Availability chart below illustrates this.
SPt SEL
SP2 Enb
n
6.4 MODULE 4 - S
" in the following parameters reflects the chosen Setpoint number. After
Select the Setpoint Output to be programmed, starting with Setpoint 1. The
Select
Select
Select the display to which the Setpoint is assigned.
The Setpoint Output Parameters are only active when an optional Setpoint
Count A
NO
YES
to exit the Setpoint programming module. The number of Setpoints
to enable Setpoint 2 and access the setup parameters. If
SEL
SPt SEL
SETPOINT 2 ENABLE (SP2 Only)
4-SEtPt
Setpoint
Setpoint Output
NO
NO
Select
SPn P-UP
Power-up
State
SETPOINT ASSIGNMENT
PARAMETER
SPn tOUt
SPn VAL
SPn OUt
SPn LIt
SPn P-UP
SPn tYPE
SPn StbY
SPn AUtO
SP1 OFF2
SP2 OFF1
SPn rSt
SPn ChC
* BOUNDARY Setpoint Action not applicable for Counter B Assignment
SETPOINT SELECT
SPt SEL
Count A
NO
NO
SP2 Enb
SP2 Only
Setpoint 2
Enable
SPn tYPE
Boundary
Setpoint
Type
Setpoint Output Time-out Value
Setpoint Value
Setpoint Output Logic
Setpoint Annunciator
Setpoint Output Power-up State
Setpoint Boundary Type
Standby Operation (Low acting only)
Counter Auto Reset
SP1 Output Off at SP2 (SP1 only)
SP2 Output Off at SP1 (SP2 only)
Output Reset with Manual Reset
Change Display Color w/ Output State
and Setpoint 2 is disabled.
SP1
YES
Count b
SPn ASN
Assignment
Setpoint
SPn StbY
DESCRIPTION
Operation
Standby
Setpoint
SP2
ETPOINT
SETPOINT PARAMETER AVAILABILITY
SPn ACt
SPt SEL
rAtE
Setpoint
Output
Action
SPn AUtO
Auto Reset
PARAMETER MENU
Counter
. Repeat
NO
O
SPn tOUt
TIMED OUT
Setpoint
Time-out
is
Output
UTPUT
COUNTER ASSIGNMENT (A or B) *
SP1 OFF2
SP1 Output
t-OUt
Off at SP2
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
SP1 Only
No
No
No
Output
11
SPn ACt
chart. Boundary output action is not applicable for Counter B assignment.
SPT ACTION DESCRIPTION
BOUNDARY
The parameter selects the action of the Setpoint Output as described in the
LAtCH
t-OUt
bOUNd
SPn VAL
bOUNd
Setpoint
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
Value
SP2 OFF1
SP2 Output
P
Off at SP1
SP2 Only
Output
ARAMETERS
LAtCH
Latched Output Mode
Timed Output Mode
Boundary Mode
(High Acting Type)
Boundary Mode
(Low Acting Type)
LATCH
LAtCH
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
Output Logic
SPn OUt
Setpoint
SETPOINT OUTPUT ACTION
Output Reset
with Manual
SPn rSt
Setpoint
Reset
TIMED OUT
t-OUt
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
LAtCH
SPn LIt
Annunciator
Setpoint
Change Display
RATE ASSIGNMENT
OUTPUT ACTIVATES
SPn ChC
Output State
Color with
Backlight
Unit Only
When Count =
When Count =
When Count
When Count
(
BOUNDARY
Setpoint
Setpoint
Setpoint
Setpoint
4-SEtPt
bOUNd
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
t-OUt
LATCH
P P r r o o
LAtCH
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
)
No
No
No
No
OUTPUT DEACTIVATES
At Manual Reset
Output Time-Out
(if
bOUNd
After Setpoint
When Count
When Count
SPn rSt
< Setpoint
Setpoint
=
YES
)