CUB5COM1 Red Lion Controls, CUB5COM1 Datasheet
CUB5COM1
Specifications of CUB5COM1
Related parts for CUB5COM1
CUB5COM1 Summary of contents
Page 1
Tel +1 (717) 767-6511 Fax +1 (717) 764-0839 www.redlion.net MODEL CUB5 - MINIATURE ELECTRONIC 8-DIGIT DUAL LISTED US LISTED R IND. CONT. EQ. 51EB GENERAL DESCRIPTION The CUB5 provides the user the ultimate in flexibility, ...
Page 2
... Power frequency magnetic fields Emissions: Emissions Notes: 1. Criterion A: Normal operation within specified limits. Refer to EMC Installation Guidelines for additional information. 12. WEIGHT: 3.2 oz (100 g) 2 PART NUMBER CUB5R000 CUB5B000 CUB5RLY0 CUB5SNK0 CUB5COM1 CUB5COM2 CUB5USB0 MLPS1000 MLPS2000 CBLPROG0 CBPRO007 1 SFCRD200 CBLUSB00 INTENSITY LEVEL TEMPERATURE 1 & 2 -35 to 75° ...
Page 3
O P PTIONAL LUG ADDING OPTION CARDS The CUB5 meters can be fitted with optional output cards and/or serial communications cards. The details for the plug-in cards can be reviewed in the specification section below. The plug-in cards, that are ...
Page 4
I NSTALLING The Plug-in cards are separately purchased option cards that perform specific functions. The cards plug into the main circuit board of the meter. After installing the cards, replace the rear cover before wiring the meter. Comms or ...
Page 5
INPUT WIRING CAUTION: Power common (PWR COMMON) is NOT isolated from input common (INP COMM). In order to preserve the safety of the meter application, the power common must be suitably isolated from hazardous live earth referenced voltage; or ...
Page 6
R EVIEWING THE KEY DISPLAY MODE OPERATION SEL Index display through enabled values RST Resets count display(s) and/or outputs OPERATING MODE DISPLAY DESIGNATORS R “ ” the left of the display is the rate value. - Counter ...
Page 7
MODULE 1-INPUt SEL INP A-b CntA dP CntA ScF CntA rSt Count Counter A Counter A Counter A Mode Decimal Point Scale Factor Reset Action Shaded area selections only apply when Counter B is enabled (Dual ...
Page 8
SCALING FOR COUNT INDICATION The CUB5’s scale factor is factory set provide one count on the display for each pulse that is input to the unit. In many applications, there will not be a one-to-one correspondence between ...
Page 9
SCALING FOR RATE INDICATION To scale the rate, enter a Scaling Display value with a corresponding Scaling Input value. These values are internally plotted to a display value of 0 and input value of 0.0 Hz. A linear relationship is ...
Page 10
MODULE 3-dSPLAY SEL SEL Enb RSt Enb Front Panel Front Panel Display Scroll Display Select Counter Enable Reset Enable FRONT PANEL DISPLAY SELECT ENABLE (SEL) SEL Enb yES NO yES yES The selection allows ...
Page 11
MODULE 4-SEtPt SP2 Only SEL SPt SEL SP2 Enb SPn ASN Setpoint Setpoint 2 Select Enable Assignment SPn P-UP SPn tYPE Setpoint Output Setpoint Power-up Boundary State Type The Setpoint Output Parameters are only active when ...
Page 12
SETPOINT OUTPUT TIME-OUT SPn tOUt 599 001 This parameter is only active if the Setpoint Action is set to time out ( Enter the value in seconds that the Setpoint ...
Page 13
MODULE 5-SEriAL SEL bAUd dAtA Baud Rate Data Bit The Serial Setup Parameters are only active when one of the optional serial communication/programming cards is installed in the meter. Refer to the CUB5USB bulletin for details ...
Page 14
Copy Procedure: 1. Connect the master and receiver using the appropriate copy cable. 2. Apply power to the meters. The receiving meter must be operating in the normal display mode (not programming mode the master meter, enter programming ...
Page 15
... Ready The customer agrees to hold Red Lion Controls harmless from, defend, and indemnify RLC against damages, claims, and expenses arising out of subsequent sales of RLC products or products containing components manufactured by RLC and based upon ...
Page 16
CUB5 PROGRAMMING QUICK OVERVIEW 16 ...