CS61584A-IL3 Cirrus Logic Inc, CS61584A-IL3 Datasheet - Page 27
![no-image](/images/manufacturer_photos/0/1/141/cirrus_logic_inc_sml.jpg)
CS61584A-IL3
Manufacturer Part Number
CS61584A-IL3
Description
Network Controller & Processor ICs IC 3.3V/5V Dul T1/E1 Line Intrfc Unit
Manufacturer
Cirrus Logic Inc
Datasheet
1.CS61584A-IQ3Z.pdf
(54 pages)
Specifications of CS61584A-IL3
Product
Framer
Number Of Transceivers
2
Data Rate
2.048 Mbps
Supply Voltage (max)
3.465 V, 5.25 V
Supply Voltage (min)
3.135 V, 4.75 V
Maximum Operating Temperature
+ 85 C
Minimum Operating Temperature
- 40 C
Mounting Style
SMD/SMT
Package / Case
PLCC-68
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Factory Test: Must be cleared for normal device
operation.
9.1.4
The Control B registers are read-write registers and
are shown in Table 8. The Control B registers select
device configuration and loopback control.
TAOS: Controls the transmission of all ones to the
line interface. A TAOS request overrides the data
transmitted to the line interface during local and re-
mote loopbacks.
RLOOP: Controls the remote loopback function for
the channel.
LLOOP1: Controls the local loopback #1 function
for the channel. Includes the jitter attenuator, if en-
abled. In host mode, selecting LLOOP1 and
DS261PP5
DS261F1
Bit
Bit
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
Control B Registers
TAOS1
RLOOP1
LLOOP11
LLOOP21
CON31
CON21
CON11
CON01
TAOS2
RLOOP2
LLOOP12
LLOOP22
CON32
CON22
CON12
CON02
Description
Description
Serial Port Address: 0x16; Parallel Port Address: 0xY6
Serial Port Address: 0x17; Parallel Port Address: 0xY7
Enable transmit all ones
Enable remote loopback
Enable local loopback #1
Enable local loopback #2
Enable transmit all ones
Enable remote loopback
Enable local loopback #1
Enable local loopback #2
Control B Register (Channel 1)
Control B Register (Channel 2)
Table 8. Control B Registers
1
1
DS261PP5
Line configuration selections
Line configuration selections
(See Transmitter section)
(See Transmitter section)
LLOOP2 simultaneously causes all ones to be out-
put from RPOS/RNEG (RDATA).
LLOOP2: Controls the local loopback #2 function
for the channel. Includes the line driver, line receiv-
er, and jitter attenuator, if enabled. See LLOOP1,
above, for receive all ones function.
CON[3:0]: Controls the configuration of the line
driver, line receiver, coder, and driver tristate as
shown in the Transmitter section. Both channels
must be configured to operate at the same rate (both
T1 or both E1).
9.1.5
In addition to the predefined T1 and E1 pulse
shapes, arbitrary pulse shapes may be created dur-
ing Host mode operation using the registers shown
in Table 9. This flexibility can be used to compen-
Definition
Definition
Disable transmit all ones
Disable remote loopback
Disable local loopback #1
Disable local loopback #2
Disable transmit all ones
Disable remote loopback
Disable local loopback #1
Disable local loopback #2
Arbitrary Waveform Registers
0
0
CS61584A
CS61584A
Reset
Reset
Value
Value
0
0
1
1
1
0
0
0
1
1
1
0
0
0
0
0
27
27