DS26528G Maxim Integrated Products, DS26528G Datasheet - Page 27
DS26528G
Manufacturer Part Number
DS26528G
Description
Network Controller & Processor ICs Octal E1-T1-J1 Singl e-Chip Transceiver (
Manufacturer
Maxim Integrated Products
Datasheet
1.DS26528G.pdf
(276 pages)
Specifications of DS26528G
Product
Framer
Number Of Transceivers
8
Supply Voltage (max)
3.465 V
Supply Voltage (min)
3.135 V
Supply Current (max)
875 mA
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Package / Case
TE-CSBGA
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
DS26528GA2
Manufacturer:
AFATECH
Quantity:
3 623
Part Number:
DS26528GA2
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
DS26528GA5+
Manufacturer:
Maxim Integrated
Quantity:
10 000
- Current page: 27 of 276
- Download datasheet (2Mb)
8.
8.1
Microprocessor control of the DS26528 is accomplished through the 28 hardware pins of the microprocessor port.
The 8-bit parallel data bus can be configured for Intel or Motorola modes of operation with the bus type select
(BTS) pin. When the BTS pin is a logic 0, bus timing is in Intel mode, as shown in
When the BTS pin is a logic 1, bus timing is in Motorola mode, as shown in
address space is mapped through the use of 13 address lines, A[12:0]. Multiplexed mode is not supported on the
processor interface.
The chip-select bar (CSB) pin must be brought to a logic-low level to gain read and write access to the
microprocessor port. With Intel timing selected, the read-data bar (RDB) and write-read bar (WRB) pins are used to
indicate read and write operations and latch data through the interface. With Motorola timing selected, the read-
write bar (RWB) pin is used to indicate read and write operations while the data-strobe bar (DSB) pin is used to
latch data through the interface.
The interrupt output pin (INTB) is an open-drain output that asserts a logic-low level upon a number of software
maskable interrupt conditions. This pin is normally connected to the microprocessor interrupt input. The device has
a bulk write mode that allows a microprocessor to write all eight internal transceivers with each bus write cycle. By
setting the BWE bit (GTCR1.2), each port write cycle will write to all four framers, LIUs, or BERTs at the same time.
The BWE bit must be cleared before normal write operation is resumed. This function is useful for device
initialization. The register map is shown in
8.2
The user should provide a system clock to the MCLK input of 2.048MHz, 1.544MHz, or a multiple of up to 8x the T1
and E1 frequencies. To meet many specifications, the MCLK source should have ±50ppm accuracy.
8.2.1 Backplane Clock Generation
The DS26528 provides facility for provision of BPCLK at 2.048MHz, 4.096MHz, 8.192MHz, 16.384MHz (see
Figure
generation. This register is also used to program REFCLKIO as an input or output. REFCLKIO can output MCLKT1
or MCLKE1 as shown in
This backplane clock and frame pulse (TSSYNCIO) can be used by the DS26528 and other IBO-equipped devices
as an IBO bus master. Hence, the DS26528 provides the 8kHz sync pulse and 4MHz, 8MHz, and 16MHz clock.
This can be used by the link layer devices and frames connected to the IBO bus.
Processor Interface
8-1). The Global Transceiver Clock Control register (GTCCR) is used to control the backplane clock
FUNCTIONAL DESCRIPTION
Clock Structure
Figure
8-1.
Figure
9-1.
27 of 276
DS26528 Octal T1/E1/J1 Transceiver
Figure 12-3
Figure 12-1
and
Figure
and
Figure
12-4. The
12-2.
Related parts for DS26528G
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN/E/DUAL PCIE/SATA HIGH SPEED SWITCH WITH INTEGRATED BIAS RESISTOR
Manufacturer:
Maxim Integrated Products
Datasheet: