TDA8932BTW NXP Semiconductors, TDA8932BTW Datasheet - Page 24

• Manufacturer Part Number: TDA8932BTW
• Description: Audio Amplifiers 2X15W BTL CLASS D AMP+VOLCTRL
• Manufacturer: NXP Semiconductors

Specifications of TDA8932BTW

• Product: Class-D
• Output Power: 55 W
• Available Set Gain: 36 dB
• Common Mode Rejection Ratio (min): 75 dB
• Thd Plus Noise: 0.007 %
• Operating Supply Voltage: 22 V
• Supply Current: 0.6 mA
• Maximum Power Dissipation: 5000 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Audio Load Resistance: 8 Ohms
• Dual Supply Voltage: +/- 11 V
• Input Signal Type: Differential
• Minimum Operating Temperature: - 40 C
• Output Signal Type: Differential, Single
• Supply Type: Single or Dual
• Supply Voltage (max): 36 V
• Supply Voltage (min): 10 V
• Output Type: 1-Channel Mono or 2-Channel Stereo
• Package / Case: HTSSOP-32
• Operational Class: Class-D
• Audio Amplifier Output Configuration: 1-Channel Mono/2-Channel Stereo
• Audio Amplifier Function: Speaker
• Total Harmonic Distortion: 0.007@8Ohm@1W%
• Single Supply Voltage (typ): 22V
• Dual Supply Voltage (typ): ±11V
• Supply Current (max): 0.195@22VmA
• Power Supply Requirement: Single/Dual
• Power Dissipation: 5W
• Rail/rail I/o Type: No
• Single Supply Voltage (min): 10V
• Single Supply Voltage (max): 36V
• Dual Supply Voltage (min): ±5V
• Dual Supply Voltage (max): ±18V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 32
• Package Type: HTSSOP EP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: TDA8932BTW/N2

NXP Semiconductors
TDA8932B_4
Product data sheet
14.2 Output current limiting
14.3 Speaker configuration and impedance
14.4 Single-ended capacitor
The peak output current I
normal operation the output current should not exceed this threshold level of 4 A
otherwise the output signal is distorted. The peak output current in SE or BTL
configurations can be estimated using
SE configuration:
BTL configuration:
Where:
Example:
A 4
running into current limiting. Current limiting (clipping) will avoid audio holes but it causes
a comparable distortion like voltage clipping.
For a flat frequency response (second-order Butterworth filter) it is necessary to change
the low-pass filter components Llc and Clc according to the speaker configuration and
impedance.
Table 14.
The SE capacitor forms a high-pass filter with the speaker impedance. So the frequency
response will roll-off with 20 dB per decade below f
I
I
Configuration
SE
BTL
O max
O max
V
R
R
R
R
P
L
DSon
s
ESR
= series resistance output inductor ( )
= supply voltage V
= load impedance ( )
speaker in the BTL configuration can be used up to a supply voltage of 18 V without
= equivalent series resistance SE capacitor ( )
= on-resistance power switch ( )
----------------------------------------------------------
R
----------------------------------------------------- -
R
Filter component values
L
L
Table 14
+
+
R
2
DSon
0.5 V
V
R
P
DSon
+
Rev. 04 — 18 December 2008
shows the practical required values.
R
R
4
6
8
4
6
8
P
DDP1
s
L
O(max)
+
+
( )
R
R
s
ESR
V
is internally limited above a level of 4 A (minimum). During
4 A
SSP1
4 A
(V) or V
Equation 5
DDP2
Llc ( H)
22
33
47
10
15
22
and
-3dB
V
SSP2
Equation
(3 dB cut-off frequency).
(V)
6.
Class-D audio amplifier
TDA8932B
Clc (nF)
680
470
330
1500
1000
680
© NXP B.V. 2008. All rights reserved.
24 of 48
(5)
(6)