NT631C-ST153B-EV3 Omron, NT631C-ST153B-EV3 Datasheet - Page 52
NT631C-ST153B-EV3
Manufacturer Part Number
NT631C-ST153B-EV3
Description
10.48-ColrDisplay,TFT,Blk,Eng
Manufacturer
Omron
Datasheet
1.NT-AL001.pdf
(315 pages)
Specifications of NT631C-ST153B-EV3
Lead Free Status / Rohs Status
Lead free / RoHS Compliant
- Current page: 52 of 315
- Download datasheet (4Mb)
3-2
Connecting to the Support Tool
Connecting to the Support Tool
1,2,3...
Note
1. In cases where there is a potential difference between the grounds of the
2. If the NT631/NT631C is installed in the same panel as equipment that gen-
Carry out grounding correctly in order to prevent operating errors due to
noise.
In order to install the system program in the NT631/NT631C, or to transmit
screen data created with the Support Tool to the NT631/NT631C, the NT631/
NT631C must be connected to a personal computer with an RS-232C cable.
The NT631/NT631C connects the RS-232C cable from a personal computer
at serial port A. When the host is connected at serial port B, the connection
with the host can be maintained as it is while the NT631/NT631C is connected
to the RS-232C cable from a personal computer.
However, when a bar code reader is being used, it must be disconnected, so
that the RS-232C cable can be connected, since they both use serial port A.
Communications Conditions
The communications conditions are automatically set when the system
installer and Support Tool are started.
Recommended Connector Cable
Use the cable indicated below.
For details on making a connector cable, refer to Appendix F Making the
Cable for Connecting a PLC.
• CV500-CN228 (length: 2 m), made by OMRON
• XW2Z-S001 (conversion cable), made by OMRON
• XW2Z-S002 (length: 2 m), made by OMRON
NT631/NT631C and the host, ground as shown in Fig. If there is some dis-
tance between the NT631/NT631C and host and grounding at a single
point is difficult, do not connect the functional ground terminal (
NT631/NT631C.
erates noise, such as a motor or inverter, do not ground the functional
ground terminal (
(D-SUB 9-pin, male ⇔ D-SUB 25-pin, male)
(D-SUB 25-pin, female ⇔ half pitch 14-pin, male)
(D-SUB 9-pin, male ⇔ D-SUB 9-pin, female)
TR M
SDA
SDB
RESET
RDA
RDB
CSA
CSB
24V
+DC
NT631/
NT631C
) of the NT631/NT631C.
PRINTER
PORT B PORT A
Grounding at a single point
Host
Serial port A
(RS-232C, 9-pin)
Section 3-2
) of the
35
Related parts for NT631C-ST153B-EV3
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
NT631-ST151 BACKLIGHT
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
NT631-ST141 BACKLIGHT
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
3M 9-9PIN CBL, NT TO AB PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
3M 9-9PIN CBL, NT TO GE PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
50CM 9-9PIN CBL, NT TO AB PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
50CM 9-9PIN CBL, NT TO GE PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
5M 9-9PIN CBL, NT TO AB PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
5M 9-9PIN CBL, NT TO GE PLC
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
10.48-ColrDisplay,TFT,Ivy,Eng
Manufacturer:
Omron
Datasheet:
Part Number:
Description:
G6S-2GLow Signal Relay
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Compact, Low-cost, SSR Switching 5 to 20 A
Manufacturer:
Omron Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Omron Corporation
Datasheet: