CYII5SC1300AB-QDC Cypress Semiconductor Corp, CYII5SC1300AB-QDC Datasheet - Page 32
![no-image](/images/manufacturer_photos/0/1/179/cypress_semiconductor_corp_sml.jpg)
CYII5SC1300AB-QDC
Manufacturer Part Number
CYII5SC1300AB-QDC
Description
SENSOR IMAGE COLOR CMOS 84-LCC
Manufacturer
Cypress Semiconductor Corp
Type
CMOS Imagingr
Specifications of CYII5SC1300AB-QDC
Pixel Size
6.7µm x 6.7µm
Active Pixel Array
1280H x 1024V
Frames Per Second
27
Voltage - Supply
3 V ~ 4.5 V
Package / Case
84-LCC
Sensor Image Color Type
Color
Sensor Image Size Range
>= 480,000Pixels
Sensor Image Size
1280x1024Pixels
Operating Supply Voltage (min)
3V
Operating Supply Voltage (typ)
3.3V
Operating Supply Voltage (max)
3.6V
Operating Temp Range
0C to 65C
Package Type
CLCC
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
84
Package
84CLCC
Image Size
1280x1024 Pixels
Color Sensing
Color
Operating Temperature
0 to 65 °C
Operating Supply Voltage
3 to 3.6 V
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Glass Lid
The IBIS5-B-1300 image sensor uses a glass lid without any coatings.
lid. As seen in
color devices.
Handling Precautions
For proper handling and storage conditions, refer to the Cypress
application note AN52561, Image Sensor Handling and Best
Practices, at www.cypress.com.
Information on Pb-Free Soldering
IBIS5-B-1300-M2 (serial numbers beyond 3694): the product
was tested successfully for Pb-free soldering processes, using a
reflow temperature profile with maximum 260°C, minimum 40s
at 255°C and minimum 90s at 217°C.
Limited Warranty
Cypress Image Sensor Business Unit warrants that the image
sensor products to be delivered hereunder if properly used and
serviced, will conform to Seller's published specifications and will
be free from defects in material and workmanship for one (1)
year following the date of shipment. If a defect were to manifest
itself within 1 (one) year period from the sale date, Cypress will
either replace the product or give credit for the product.
Return Material Authorization (RMA)
Cypress packages all of its image sensor products in a clean
room environment under strict handling procedures and ships all
image sensor products in ESD-safe, clean room-approved
shipping containers. Products returned to Cypress for failure
analysis should be handled under these same conditions and
packed in its original packing materials, or the customer may be
liable for the product.
Document #: 38-05710 Rev. *H
Figure
31, the sensor does not use infrared attenuating color filter glass. Provide a filter in the optical path when using
Figure 31. Transmission Characteristics of Glass Lid
RoHS (Pb-free) Compliance
This paragraph reports the use of hazardous chemical
substances as required by the RoHS Directive (excluding
packing material).
Lead, Cadmium, Mercury Hexavalent Chromium, PBB (Polybro-
minated biphenyls), PBDE (Polybrominated diphenyl ethers),
noted as “intentional content: is not available in the
IBIS5-B-1300.
Note ‘Intentional content’ is defined as any material demanding
special attention that is allowed into the product as follows:
■
■
The following case is not treated as ‘intentional content’:
■
A chemical composition is added into the inquired product
intentionally to produce and maintain the required performance
and function of the product.
A chemical composition which is used intentionally in the
manufacturing process, that is allowed into the product.
The above material is contained as an impurity into raw
materials or parts of the intended product. The impurity is
defined as a substance that cannot be removed industrially, or
it is produced using a process such as chemical composing or
reaction, and it cannot be removed technically.
Figure 31
shows the transmission characteristics of the glass
CYII5SM1300AB
Page 32 of 35
[+] Feedback