EPM7160STC100-6N Altera, EPM7160STC100-6N Datasheet - Page 53
![MAX 7000/S/AE/B](/photos/37/16/371667/544-100-tqfp_sml.jpg)
EPM7160STC100-6N
Manufacturer Part Number
EPM7160STC100-6N
Description
MAX 7000/S/AE/B
Manufacturer
Altera
Datasheet
1.EPM7160STC100-6N.pdf
(66 pages)
Specifications of EPM7160STC100-6N
Family Name
MAX 7000S
Memory Type
EEPROM
# Macrocells
160
Number Of Usable Gates
3200
Frequency (max)
166.7MHz
Propagation Delay Time
6ns
Number Of Logic Blocks/elements
10
# I/os (max)
84
Operating Supply Voltage (typ)
5V
In System Programmable
Yes
Operating Supply Voltage (min)
4.75V
Operating Supply Voltage (max)
5.25V
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Mounting
Surface Mount
Pin Count
100
Package Type
TQFP
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Notes to tables:
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
Power
Consumption
Altera Corporation
These values are specified under the recommended operating conditions shown in
information on switching waveforms.
This minimum pulse width for preset and clear applies for both global clear and array controls. The t
must be added to this minimum width if the clear or reset signal incorporates the t
path.
This parameter is a guideline that is sample-tested only and is based on extensive device characterization. This
parameter applies for both global and array clocking.
These parameters are measured with a 16-bit loadable, enabled, up/down counter programmed into each LAB.
The f
Operating conditions: V
For EPM7064S-5, EPM7064S-6, EPM7128S-6, EPM7160S-6, EPM7160S-7, EPM7192S-7, and EPM7256S-7 devices,
these values are specified for a PIA fan-out of one LAB (16 macrocells). For each additional LAB fan-out in these
devices, add an additional 0.1 ns to the PIA timing value.
The t
running in the low-power mode.
LPA
MAX
parameter must be added to the t
values represent the highest frequency for pipelined data.
CCIO
Supply power (P) versus frequency (f
is calculated with the following equation:
P = P
The P
and switching frequency, can be calculated using the guidelines given in
Application Note 74 (Evaluating Power for Altera
The I
application logic, is calculated with the following equation:
I
A × MC
The parameters in this equation are shown below:
MC
MC
MC
f
tog
A, B, C
CCINT
MAX
= 3.3 V ± 10% for commercial and industrial use.
LC
TON
DEV
USED
CCINT
INT
IO
=
TON
value, which depends on the device output load characteristics
+ P
= Number of macrocells with the Turbo Bit option turned on,
= Number of macrocells in the device
= Total number of macrocells in the design, as reported
= Highest clock frequency to the device
= Average ratio of logic cells toggling at each clock
= Constants, shown in
value, which depends on the switching frequency and the
IO
+ B × (MC
LAD
as reported in the MAX+PLUS II Report File (.rpt)
in the MAX+PLUS II Report File (.rpt)
(typically 0.125)
= I
, t
CC INT
LAC
MAX 7000 Programmable Logic Device Family Data Sheet
, t
IC
DEV
× V
, t
EN
– MC
CC
, t
SEXP
+ P
TON
, t
IO
ACL
Table 39
) + C × MC
MAX
, and t
in MHz) for MAX 7000 devices
CPPW
Table
Devices).
LAD
USED
parameters for macrocells
parameter into the signal
14. See
× f
MAX
Figure 13
× tog
LPA
parameter
for more
LC
53