ADIS16334/PCBZ Analog Devices Inc, ADIS16334/PCBZ Datasheet - Page 19

no-image

ADIS16334/PCBZ

Manufacturer Part Number
ADIS16334/PCBZ
Description
ADIS16334/PCB EVAL. BD. PB Free
Manufacturer
Analog Devices Inc
Series
iSensor™r
Datasheet

Specifications of ADIS16334/PCBZ

Sensor Type
Gyroscope, 3 Axis
Sensing Range
±75 ~ 300°/s
Interface
Serial
Sensitivity
0.0125°/sec/LSB
Embedded
No
Utilized Ic / Part
ADIS16334
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Supply
-
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
APPLICATIONS INFORMATION
ADIS16334/PCBZ
The ADIS16334/PCBZ includes one ADIS16334BLMZ, one
interface PCB, and one interface flex. This combination of
components enables quicker installation for prototype evaluation
and algorithm development. Figure 23 provides a mechanical
design example for using these three components in a system.
20.15mm
NOTES
1. USE FOUR M2 MACHINE SCREWS TO ATTACH
2. USE FOUR M3 MACHINE SCREWS TO ATTACH
Figure 24 provides the pin assignments for the interface board,
when it is properly connected to the ADIS16334BMLZ in this
manner.
THE ADIS16334BMLZ.
THE INTERFACE PCB.
10.07mm
ADIS16334AMLZ
DNC
GND
GND
VCC
RST
SCDL-101470-1-CLM-FTMH-1
CS
Figure 23. Physical Diagram for Mounting the ADIS16334/PCBZ
11
1
3
5
7
9
Figure 24. J1/J2 Pin Assignments for Interface PCB
J1
(SAMTEC P/N)
28.40mm
10
12
2
4
6
8
SCLK
DOUT
DIN
GND
VCC
VCC
15mm TO
45mm
DIO2
DNC
DNC
GND
DNC
DNC
11
1
3
5
7
9
23.75mm
12
12
2
2
J2
J1
J2
INTERFACE PCB
11
11
1
1
10
12
2
4
6
8
15.05mm
GND
DIO3
DIO4
DNC
DNC
DIO1
30.10mm
Rev. 0 | Page 19 of 20
Installation
The following steps provide an example installation process for
using these three components:
The ADIS16334 does not require external capacitors for normal
operation; therefore, the interface PCB does not use the C1/C2
pads (not shown in Figure 23).
Drill and tap M2 and M3 holes in the system frame, according
to the locations in Figure 23. The distance between these
components is flexible but make sure that the hole-to-hole
distance is within the 15 mm to 45 mm range shown in the
diagram.
Install the ADIS16334 using M2 machine screws. Use a
mounting torque of 25 inch-ounces.
Install the interface PCB using M3 machine screws.
Connect J1 on the interface flex to the ADIS16334BMLZ
connector.
Connect J2 on the interface flex to J3 on the interface PCB.
Note that J2 (interface flex) has 20 pins and J3 (interface PCB)
has 24 pins. Make sure that Pin 1 on J2 (interface flex)
connects to Pin 20 on J3 (interface PCB). J3 has a Pin 1
indicator to help guide this connection.
Connect the ADIS16334BMLZ power, ground, and SPI
signals to an embedded processor board using J1 and a
12-pin, 1 mm ribbon cable system. The following parts may
be useful in building this type of cable: 3M Part Number
152212-0100-GB (ribbon crimp connector) and 3M Part
Number 3625/12 (ribbon cable).
Connect the ADIS16334BMLZ auxiliary I/O functions to
the embedded processor board using J2 and the same type
of ribbon cable system as J1.
ADIS16334

Related parts for ADIS16334/PCBZ