PIC-MCP Olimex Ltd., PIC-MCP Datasheet

Programmers & Debuggers PICSTART+EMULATOR ICSP 12

PIC-MCP

Manufacturer Part Number

PIC-MCP

Description

Programmers & Debuggers PICSTART+EMULATOR ICSP 12

Manufacturer

Olimex Ltd.

Datasheet

1.PIC-MCP.pdf (1 pages)

Specifications of PIC-MCP

Positions/sockets

Description/function

PICSTART Programmer/Emulator

Lead Free Status / RoHS Status

Lead free / RoHS Compliant

For Use With/related Products

PIC MCUs

Current page: 1 of 1
Download datasheet (45Kb)

What is PIC-MCP?

PIC-MCP is MPLAB® compatible programmer for

PICmicro

development programmer that enables you to program

user software into PICmicro microcontroller devices

(DIP

replacement for Microchip PicStart+® programmer, it

programs faster than PicStart+® and have ICSP

connector for in-circuit programming of PICmicro

microcontrollers.

Note: PIC-MCP Programmer is designed for use in

firmware development and is not intended for

production use.

What PIC-MCP package contains?

The PIC-MCP package contain completely assembled

and tested board with RS232 port, ZIF socket and

ICSP connector + ICSP cable which is compatible

with all Olimex’s PIC-Pxx prototype boards.

The package doesn’t include RS232 cable and power

supply adapter 18VDC.

The latest MPLAB software can be free download

from Microchip’s web site http://www.microchip.com.

What PIC-MCP does?

The PIC-MCP development programmer has the

following features: blank check, read, program, verify

PICmicro microcontrollers.

How to install PIC-MCP?

To work with PIC-MCP you have to attach the RS232

cable and to apply power supply.

packages

Development boards for PIC, AVR and MSP430 microcontrollers http://www.olimex.com/dev

microcontrollers.

only).

PIC-MCP

PIC MICROCONTROLLER PROGRAMMER

It’s

PIC-MCP-C MPLAB® COMPATIBLE

microcontroller

low

cost

The RS232 cable should be with 9-pin D type

connector. The cable should have all necessary signals

as GND, Rx, Tx, CTS, RTS. This cable is NOT a null

modem cable.

The power supply adapter should be 18VDC

>=100mA on the center positive 2.5 mm terminal.

When the power supply is applied the Green LED

PWR will switch ON.

WARNING: DO NOT connect power with a device

in the socket. Damage to the device may result.

How to use PIC-MCP ICSP programming?

The in-circuit programming connector is very useful

when you have to program PICmicro installed on

circuit boards or PICmicro in SMD packages, which

can’t be programmed with ZIF socket.

To enable ICSP programming the JP jumper should be

shorted with the cap. Please note that when JP is

shorted the PICmicro in ZIF socket is not programmed

and only the ICSP connector is enabled!

ICD/ICSP connector layout:

The ICD/ICSP connector is 6 pin with 0,1" step. The

PIN.1 is marked with square pad on bottom and arrow

on top. ICSP signals are: 1- MCLR, 2- VDD, 3-

VSS/GND, 4- PGD/RB7, 5- PGC/RB6, 6- PGM/RB3.

How to use PIC-MCP with MPLAB?

Please read the detailed instructions in MPLAB

help file

What devices PIC-MCP programs?

PIC-MCP

microcontrollers except PIC17XXX series.

PIC-MCP will program all devices which are

supported by the latest release of MPLAB.

Olimex will publish firmware upgrade after each

new MPLAB release.

Ordering codes:

PIC-MCP

programs

- assembled and tested

all

PICmicro

Related parts for PIC-MCP

Related keywords

PIC-MCP datasheet
PIC-MCP data sheet
PIC-MCP pdf datasheet
PIC-MCP component
PIC-MCP part
PIC-MCP distributor
PIC-MCP RoHS
PIC-MCP datasheet download