OM13005,598 NXP Semiconductors, OM13005,598 Datasheet - Page 11

• Manufacturer Part Number: OM13005,598
• Description: BOARD EVAL EM773 METER US PLUG
• Manufacturer: NXP Semiconductors
• Type: Other Power Managementr

Specifications of OM13005,598

• Design Resources: Plug Meter Schematics, Gerber Files USB Dongle Schematics, Gerber Files
• Main Purpose: Power Management, Energy/Power Meter
• Embedded: Yes, MCU, 32-Bit
• Utilized Ic / Part: EM773FHN33,551
• Interface Type: USB
• Maximum Operating Temperature: + 150 C
• Operating Supply Voltage: 1.8 V to 3.6 V
• Product: Power Management Development Tools
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Primary Attributes: -
• Secondary Attributes: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• For Use With/related Products: EM773, OL2381
• Other names: 568-6680

NXP Semiconductors
EM773
Objective data sheet
7.8.1 Features
7.9.1 Features
7.10 I
7.9 SPI serial I/O controller
The UART includes a fractional baud rate generator. Standard baud rates such as
115200 Bd can be achieved with any crystal frequency above 2 MHz.
The EM773 contains one SPI controller.
The SPI controller is capable of operation on a SSP, 4-wire SSI, or Microwire bus. It can
interact with multiple masters and slaves on the bus. Only a single master and a single
slave can communicate on the bus during a given data transfer. The SPI supports full
duplex transfers, with frames of 4 bits to 16 bits of data flowing from the master to the
slave and from the slave to the master. In practice, often only one of these data flows
carries meaningful data.
The EM773 contains one I
The I
(SCL) and a Serial DAta line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (e.g., an LCD driver) or a transmitter with the
capability to both receive and send information (such as memory). Transmitters and/or
receivers can operate in either master or slave mode, depending on whether the chip has
to initiate a data transfer or is only addressed. The I
controlled by more than one bus master connected to it.
2
•
•
•
•
•
•
•
•
•
•
•
•
•
•
C-bus serial I/O controller
Maximum UART data bit rate of 3.125 MBit/s.
16 Byte Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in fractional baud rate generator covering wide range of baud rates without a
need for external crystals of particular values.
FIFO control mechanism that enables software flow control implementation.
Support for RS-485/9-bit mode.
Support for modem control.
Maximum SPI speed of 25 Mbit/s (master) or 4.17 Mbit/s (slave) (in SSP mode)
Compatible with Motorola SPI, 4-wire Texas Instruments SSI, and National
Semiconductor Microwire buses
Synchronous serial communication
Master or slave operation
8-frame FIFOs for both transmit and receive
4-bit to 16-bit frame
2
C-bus is bidirectional for inter-IC control using only two wires: a Serial Clock Line
All information provided in this document is subject to legal disclaimers.
Rev. 1 — 1 September 2010
2
C-bus controller.
2
C is a multi-master bus and can be
Energy metering IC
© NXP B.V. 2010. All rights reserved.
EM773
11 of 45