CP-BNCPC-017 Emerson Network Power, CP-BNCPC-017 Datasheet - Page 233

• Manufacturer Part Number: CP-BNCPC-017
• Manufacturer: Emerson Network Power
• Type: BNCr

Specifications of CP-BNCPC-017

• Gender: RCP
• Body Style: Right Angle
• Terminate To: PCB
• Mounting Style: Through Hole
• Termination: Solder
• Operating Temp Range: -55C to 85C
• Operating Frequency: 0 to 4
• Body Plating: Nickel
• Contact Plating: Gold
• Contact Material: Brass/BeCu
• Body Material: Zinc/Brass
• Impedance: 50Ohm
• Lead Free Status / RoHS Status: Compliant

Right Angle SMA Low Loss
Diameter .195, .200 and .240
Connectivity Solutions
Tel: [phone]
•
Fax: [phone]
LOW LOSS DIA.
0.195
0.200
0.240
Assembly Instructions
1. Identify connector parts. (3 piece parts)
2. Strip cable to dimensions shown. Do not nick braid, foil or center
3. Flare braid and slide body assembly over foil and dielectric,
4. Arrange braid uniformly around crimp stem. Slide crimp sleeve
conductor. Cut foil flush with dielectric, do not remove foil. Make
sure that dielectric is clean and free from all particles. Tin cen-
ter conductor, keeping solder amount to a minimum. Slide crimp
sleeve onto jacket of cable.
then under braid. Make sure cable center conductor is con-
tained within connector contact, but do not allow foil and
dielectric to enter body access port. Solder center conductor to
contact through the rear access port. Use a minimum amount
of solder for a full fillet joint. .020 (0.51) Diameter solder is
recommended.
forward and crimp using Johnson hand crimp tool 141-0000-
913 and recommended crimp die hex. Place expansion cap in
access port and seat with recommended Diameter flat punch.
•
.110 (2.79)
.110 (2.79)
.135 (3.43)
www.EmersonNetworkPower.com/connectivity
“A”
INCHES (MILLIMETERS) • CUSTOMER DRAWINGS AVAILABLE ON REQUEST
CABLE GROUP
LMR-195
LMR-200
LMR-240
LMR-195
LMR-200
LMR-240
LMR-195
LMR-200
LMR-240
CRIMP DIE HEX
.213 (5.41) hex
.213 (5.41) hex
.255 (6.48) hex
142-0407-101
142-0407-106
142-4439-101
142-4439-106
142-0435-101
142-0435-106
142-5407-101
142-5407-106
142-0439-101
142-0439-106
142-5435-101
142-5435-106
142-4407-101
142-4407-106
142-5439-101
142-5439-106
142-4435-101
142-4435-106
PART NO.
FLAT PUNCH DIA.
.187 (4.75)
.187 (4.75)
.242 (6.15)
CRIMP HEX
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.255 (6.48)
.255 (6.48)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.255 (6.48)
.255 (6.48)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.213 (5.41)
.255 (6.48)
.255 (6.48)
233