EVAL-AD5754REBZ Analog Devices Inc, EVAL-AD5754REBZ Datasheet - Page 30

• Manufacturer Part Number: EVAL-AD5754REBZ
• Description: D/A Converter Evaluation Board
• Manufacturer: Analog Devices Inc

Specifications of EVAL-AD5754REBZ

• Silicon Manufacturer: Analog Devices
• Application Sub Type: DAC
• Kit Application Type: Data Converter
• Silicon Core Number: AD5754
• Number Of Dac's: 4
• Number Of Bits: 16
• Outputs And Type: 4, Single Ended
• Sampling Rate (per Second): *
• Data Interface: Serial
• Settling Time: 10µs
• Dac Type: Voltage
• Voltage Supply Source: Dual ±
• Operating Temperature: -40°C ~ 85°C
• Utilized Ic / Part: AD5754
• Development Tool Type: Hardware / Software - Eval/Demo Board
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

AD5724R/AD5734R/AD5754R
DESIGN FEATURES
ANALOG OUTPUT CONTROL
In many industrial process control applications, it is vital that
the output voltage be controlled during power-up. When the
supply voltages change during power-up, the V
clamped to 0 V via a low impedance path (approximately 4 kΩ).
To prevent the output amplifiers from being shorted to 0 V
during this time, Transmission Gate G1 is also opened (see
Figure 48). These conditions are maintained until the power
supplies have stabilized and a valid word is written to a DAC
register. At this time, G2 opens and G1 closes.
POWER-DOWN MODE
Each DAC channel of the AD5724R/AD5734R/AD5754R can
be individually powered down. By default, all channels are in
power-down mode. The power status is controlled by the power
control register (see Table 27 and Table 28 for details). When a
channel is in power-down mode its output pin is clamped to
ground through a resistance of approximately 4 kΩ and the
output of the amplifier is disconnected from the output pin.
OVERCURRENT PROTECTION
Each DAC channel of the AD5724R/AD5734R/AD5754R
incorporates individual overcurrent protection. The user has
two options for the configuration of the overcurrent protection:
constant current clamp or automatic channel power-down. The
configuration of the overcurrent protection is selected via the
clamp enable bit in the control register.
VOLTAGE
CONTROL
Figure 48. Analog Output Control Circuitry
MONITOR
AND
G1
G2
V
OUT
OUT
A
x pins are
Rev. C | Page 30 of 32
Constant Current Clamp (Clamp Enable = 1)
If a short circuit occurs in this configuration, the current is
clamped at 20 mA. This event is signaled to the user by the
setting of the appropriate overcurrent (OC
control register. Upon removal of the short-circuit fault, the
OC
Automatic Channel Power-Down (Clamp Enable = 0)
If a short circuit occurs in this configuration, the shorted
channel powers down and its output is clamped to ground via
a resistance of approximately 4 kΩ. Also, at this time, the output
of the amplifier is disconnected from the output pin. The short-
circuit event is signaled to the user via the overcurrent bits (OC
while the power-up bits (PU
powered down. After the fault is rectified, the channels can be
powered up again by setting the PU
THERMAL SHUTDOWN
The AD5724R/AD5734R/AD5754R incorporate a thermal
shutdown feature that automatically shuts down the device if
the core temperature exceeds approximately 150°C. The thermal
shutdown feature is disabled by default and can be enabled
via the TSD enable bit of the control register. In the event of a
thermal shutdown, the TSD bit of the power control register is set.
INTERNAL REFERENCE
The on-chip voltage reference is powered down by default. If
an external voltage reference source is to be used, the internal
reference must remain powered down at all times. If the internal
reference is to be used as the reference source, it must be powered
up via the PU
reference voltage is accessible at the REFIN/REFOUT pin for use
as a reference source for other devices within the system. If the
internal reference is to be used external to the AD5724R/
AD5734R/AD5754R, it must first be buffered.
X
bit is cleared.
REF
bit of the power control register. The internal
X
) indicate which channels have
X
bits.
X
) bit in the power
X
),