PH100S280-5 TDK Corporation, PH100S280-5 Datasheet - Page 34

• Manufacturer Part Number: PH100S280-5
• Description: Power Supply, Power Rating 100 Watt, Output Current Rating 20.00 Ampere
• Manufacturer: TDK Corporation

Specifications of PH100S280-5

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PH
B-332
PH
Pay attention to all warnings and cautions before using the unit.
Incorrect usage could lead to an electric shock, damage to unit,
or a fire hazard. Be sure read below warnings and cautions bef
ore using the power module.
● Do not touch heatsink and case which may be hot.
● Do not open the case and touch the internal components. They
● When the unit is operating, keep your hands and face away from
● Confirm that connections to input/output terminals and signal
● Attach a fast blow type external fuse to each module to ensure
● This power supply is designed for professional installation within
● For 48V input voltage, use isolated voltage by reinforced insula-
1 INPUT VOLTAGE RANGE
Input voltage ranges of PH series are as follows.
For 110VDC input model, it is necessary to derate the out-
put power when the input voltage range is in the range of
82 - 88V.
may have high temperature or high voltage which may get you in
electric shock or burned.
the unit. You may get injured by an accident.
terminals are correct as indicated in the instruction manual.
safety operation and to acquire each safety approval.
an end user equipment.
tion at primary power supply or double insulation as input power
100
50 - 150, 75 - 300F
Warning
Caution
80
60
40
0
24VDC Input: 18 - 36VDC
48VDC Input: 36 - 76VDC
110VDC Input: 82 - 185VDC
280VDC Input: 200 - 400VDC
80
PH50 - 150, 75 - 300F Instruction Manual
Input Voltage ( VDC )
1. Explanations on Specifications
90
Before Using The Power Supply
100
110
120
● The output from this power module must be considered as an
● The application circuits and their parameters are for reference
● The information on this document is subject to change without
● No part of this document may be copied or reproduced in any
CE Marking, when applied to a product covered by this instruction
manual, indicates compliance with the low voltage directive (73/23/
EEC) as modified by the CE Marking Directive (93/68/EEC) which
complies with EN60950.
Input voltage normally includes the ripple voltage (Vr
shown in Figure1-2. The ripple voltage shall be less than
the following values.
When ripple voltage exceeds the above value, the output
ripple voltage may become larger. Also, the output voltage
may rise as the input voltage is fluctuated in dynamic line.
The peak of input voltage wave shall be within the input
voltage range.
source.
energy hazard (>240VA power and 2V voltage) and must not be
accesible to an end user. End equipment manufacturers must
provide protection against inadvertent contact with the output
terminals on this product by a service engineer or by service en-
gineer dropping a tool into them.
only. Be sure to verify effectiveness of application circuits and
their parameters before finalizing circuit design.
notice. For actual design-in, please refer to the latest publica-
tions of data sheet, etc., for the most up-to-date specifications of
this unit.
form or by any means without prior written consent of Densei-
Lambda.
Note : CE Marking
図1?1 PH110シリーズ出力ディレーティング
100
80
60
40
0
Figure1-1: PH110 Series Output Derating
24VDC Input: 2V
48VDC Input: 4V
110VDC Input: 10V
280VDC Input: 20V
80
・All specifications are subject to change without notice.
Input Voltage ( VDC )
90
100
110
120
pl
) as