B72482S9999X2 EPCOS Inc, B72482S9999X2 Datasheet
B72482S9999X2
Specifications of B72482S9999X2
Related parts for B72482S9999X2
B72482S9999X2 Summary of contents
Page 1
Ceramic transient voltage suppressors Leaded transient voltage/RFI suppressors (SHCVs) Series/Type: Date: August 2008 © EPCOS AG 2008. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. ...
Page 2
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series EPCOS type designation system for leaded transient voltage / RFI suppressors Leaded, SHCV series EIA case sizes of used chips 3 ...
Page 3
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Features RFI noise suppression and transient overvoltage protection integrated in a single component Reliable protection against automotive transients such as load dump and jump start (for SR1 and SR2 types) High capacitance (up ...
Page 4
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Temperature derating Climatic category: 55/+125 C Please read Cautions and warnings and Important notes at the end of this document. Page ...
Page 5
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Electrical specifications and ordering codes Maximum ratings (T = 125 C) op,max Type Ordering code SR1S14BM105X B72587G3140S200 SR1S14BM155X B72587H3140S200 SR1S14BM474X B72587E3140S200 SR2S14BM155X B72547H3140S200 SR2S14BM474X B72547E3140S200 SR2S14BM475X B72547L3140S200 SR6K14M224X B72527C3140K000 SR1K20M105X B72587G3200K000 SR1K20M155X B72587H3200K000 ...
Page 6
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Dimensional drawing Delivery mode Designation Taping mode - Bulk G Taped on reel GA Taped in AMMO pack M14 Lead length 14 mm Standard delivery mode for SHCV types is bulk. Taped versions ...
Page 7
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Typical characteristics Capacitance change C/C versus temperature T 25 Note: The capacitance and the dissipation factor shall meet the specified values 1000 hours after the last heat treatment above the curie temperature. Please ...
Page 8
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series V/I characteristics SR1S14B* SR2S14B* Please read Cautions and warnings and Important notes at the end of this document. Page ...
Page 9
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series V/I characteristics SR6K14* SR1K20* Please read Cautions and warnings and Important notes at the end of this document. Page ...
Page 10
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series V/I characteristics SR2K20* SR6K20* Please read Cautions and warnings and Important notes at the end of this document. Page ...
Page 11
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series V/I characteristics SR6K35* Please read Cautions and warnings and Important notes at the end of this document. Page ...
Page 12
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Derating curves Maximum surge current I surge,max For explanation of the derating curves refer to "General technical information", chapter 2.7.2 SHCV-SR1 ... SHCV-SR2 ... Please read Cautions and warnings and Important notes at ...
Page 13
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Derating curves Maximum surge current I surge,max For explanation of the derating curves refer to "General technical information", chapter 2.7.2 SR6K14 , SR6K20 SR6K35 ... Please read Cautions and warnings and Important notes ...
Page 14
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Soldering directions 1 Terminations 1.1 Nickel barrier termination The nickel barrier layer of the silver/nickel/tin termination prevents leaching of the silver base met- allization layer. This allows great flexibility in the selection of ...
Page 15
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series 2 Recommended soldering temperature profiles 2.1 Reflow soldering temperature profile Recommended temperature characteristic for reflow soldering following JEDEC J-STD-020D Profile feature Preheat and soak - Temperature min - Temperature max - Time Average ...
Page 16
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series 2.2 Wave soldering temperature profile Temperature characteristics at component terminal with dual-wave soldering 2.3 Lead-free soldering processes EPCOS multilayer CTVS with AgNiSn termination are designed for the requirements of lead-free soldering processes only. ...
Page 17
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series 3 Recommended soldering methods - type-specific releases by EPCOS 3.1 Overview Type Case size CT... / CD... 0201/ 0402 CT... / CD... 0603 ... 2220 CN... 0603 ... 2220 Arrays 0405 ... 1012 ...
Page 18
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series If the solder meniscus is too high, i.e. the solder quantity is too large, the vise effect may occur. As the solder cools down, the solder contracts in the direction of the component. ...
Page 19
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series 5 Conductive adhesion Attaching surface-mounted devices (SMDs) with electrically conductive adhesives is a commer- cially attractive method of component connection to supplement or even replace conventional sol- dering methods. Electrically conductive adhesives consist ...
Page 20
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series 6 Solderability tests Test Standard Wettability IEC 60068-2-58 Leaching IEC resistance 60068-2-58 Thermal shock (solder shock) Tests of resistance IEC to soldering heat 60068-2-58 for SMDs Tests of resistance IEC to soldering heat ...
Page 21
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Note: Leaching of the termination Effective area at the termination might be lost if the soldering temperature and/or immersion time are not kept within the recommended conditions. Leaching of the outer electrode should ...
Page 22
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series 7.5 Adhesive application Thin or insufficient adhesive causes chips to loosen or become disconnected during curing. Low viscosity of the adhesive causes chips to slip after mounting advised to consult the ...
Page 23
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series 7.10 Standards CECC 00802 IEC 60068-2-58 IEC 60068-2-20 JEDEC J-STD-020D Please read Cautions and warnings and Important notes at the end of this document. Page ...
Page 24
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Symbols and terms Symbol Term C Typical capacitance per line line,typ C Maximum capacitance max C Minimum capacitance min C Nominal capacitance nom C Tolerance of nominal capacitance nom C Typical capacitance typ ...
Page 25
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series V Maximum AC operating voltage, root-mean-square value RMS,max V Varistor voltage (also termed breakdown voltage Minimum varistor voltage V,min V Maximum varistor voltage V,max V Tolerance of varistor voltage V W ...
Page 26
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Cautions and warnings General Some parts of this publication contain statements about the suitability of our ceramic transient voltage suppressor (CTVS) components (multilayer varistors (MLVs), CeraDiodes, ESD/EMI fil- ters, SMD disk varistors (CU ...
Page 27
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series therefore not advisable, and it is only allowed together with safety countermeasures like thermal fuses. Storage Only store CTVS in their original packaging. Do not open the package before storage. Storage conditions in ...
Page 28
Leaded transient voltage/RFI suppressors (SHCVs) SHCV series Conductive adhesive gluing Only multilayer varistors (MLVs) with an AgPd termination are approved for conductive adhesive gluing. Operation Use CTVS only within the specified operating temperature range. Use CTVS only within specified voltage ...
Page 29
Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical ...