PAXCDC2C Red Lion Controls, PAXCDC2C Datasheet - Page 20

• Manufacturer Part Number: PAXCDC2C
• Description: Extnd. RS232 Card W/9 Pin D Connector
• Manufacturer: Red Lion Controls

Specifications of PAXCDC2C

• Brand/series: PAXDR
• Card Type: Option Communications
• Communication: Serial RS232
• Data Protocols: 7/8 bits, 300 to 19,200 baud, no, even or odd parity
• Pax Label Kit: 189 Different Engineering Units, Labels Inserted Inside the Unit
• Lead Free Status / Rohs Status: RoHS Compliant part


“
the chosen setpoint is programmed, the display will default to
the next setpoint to be programmed and continue the sequence for each setpoint.
Pressing PAR at

deactivated. Reverse (
deactivated.

6.6 MODULE 6 - S
” in the following parameters will reflect the chosen setpoint number.) After

Select a setpoint (alarm output) to open the remaining module menu. (The

Normal (
PAR
6-SPt
SPSEL
Setpoint
* BOUNDARY is the only Setpoint Action available for setpoints assigned to Totalizer C.

Select
















PAR
PARAMETER

be installed into the PAX (see Ordering Information). Depending on the card installed, there will be two or four setpoint outputs
available. This section replaces the bulletin that comes with the setpoint plug-in card. Please discard the separate literature when using
the Plug-in card with the PAXDR. For maximum input frequency, unused Setpoints should be configured for


Operation
) turns the output “on” when activated and “off” when
Standby

Stb-n
Module 6 is the programming for the setpoint (alarms) output parameters. To have setpoint outputs, a setpoint Plug-in card needs to
The Setpoint Assignment and the Setpoint Action determine certain setpoint parameter availability. The chart below illustrates this.
SETPOINT OUTPUT LOGIC

) turns the output “off” when activated and “on” when
SETPOINT SELECT
OUt-n
will exit Module 6.
Output
Logic


Setpoint Output Logic
Setpoint Annunciator
Setpoint Power-Up State
Setpoint Value
Setpoint Tracking
Setpoint Boundary Type
Setpoint Standby Operation
Setpoint Hysteresis
Setpoint Off Delay
Setpoint On Delay
Setpoint Time Out
Totalizer Auto Reset
Reset With Display Reset
Reset When Spn+1 Activates
Reset When Spn+1 Deactivates

Hysteresis
Setpoint
HYS-n
Annunciator
DESCRIPTION

Setpoint
LIt-n


tOFF-n
Off Time
Delay
SETPOINT PARAMETER AVAILABILITY
ETPOINT
Assignment
Setpoint
ASN-n

On Time

tON-n
Delay
PARAMETER MENU
TIMED OUT
. Select
Setpoint
ACt-n
Action

Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
(A
tOUt-n
Time-out
Value
LARM
20
RATE ASSIGNMENT
BOUNDARY
Power-up

the corresponding setpoint annunciator of an “on” alarm output. Reverse (
displays the corresponding setpoint annunciator of an “off” alarm output.

“on” alarm output.


SUP-n
State
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No



Select the display to which the setpoint is assigned.
Auto Reset
AUtO-n

Totalizer
) P
disables the display of the setpoint annunciator. Normal (
flashes the display and the corresponding setpoint annunciator of an

ARAMETERS
Setpoint

LATCH


Value
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
No
SP-n
when Display
Output Reset
Resets
SETPOINT ANNUNCIATORS
rSd-n
SETPOINT ASSIGNMENT
TIMED OUT



Tracking

trC-n
Setpoint
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No
Output Reset
when SPn+1
rSAS-n
Activates
TOTALIZER ASSIGNMENT


(
BOUNDARY *


action.
Boundary


tYP-n
Yes
Yes
Yes
Yes
Yes
Yes
Type
No
No
No
No
No
No
No
No
No
Output Reset
when SPn+1
Deactivates
rSAE-n



)

LATCH
Pro
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
No
No
No
No


) displays

)