V45450-1 VEEDER ROOT, V45450-1 Datasheet - Page 191

• Manufacturer Part Number: V45450-1
• Description: Multifunction Counter
• Manufacturer: VEEDER ROOT
• Type: Counterr

Specifications of V45450-1

• No. Of Digits / Alpha: 4
• Digit Height: 10mm
• Counting Speed: 10kHz
• Operating Temperature Range: 0°C To +55°C
• Character Size: 10mm
• Panel Cutout Width: 1.77"
• Connection Type: Screw
• Counter Type: Predetermining
• Cut Out, Panel: 1/16 DIN
• Dimensions: 1.89"L×4.33"W×1.89"H
• Display Digit Height: 10mm (Top Display), 7mm (Bottom Display)
• Display Type: LED
• Frequency, Operating: 50⁄60 Hz
• Function: Counter
• Input Type: NPN
• Mounting Type: Panel
• Number Of Digits: 6
• Primary Type: Electronic
• Standards: UL and cUL Recognized, CE Marked
• Temperature, Operating, Range: 0 to +50 °C
• Terminal Type: Screw Terminal
• Termination: Screw Terminal
• Voltage, Supply: 90 to 264 VAC
• Weight: 7 Oz.
• Input Signals Accepted From A Variety Of Sources: Dry Contact, PNP or NPN Sensors, Encoders
• Lead Free Status / RoHS Status: na

MAX Roll Diameter Monitor and Control (R.D.M.C.) combines all of the
measurement and control functions for windup and unwind applications
in a single, economical unit. Productivity improvements are made
through the elimination of expensive scrap and automation of time-
consuming rethreading.
MAX R.D.M.C.'s optional analog output provides a voltage signal
directly or inversely proportional to the measured diameter for use in
data recording, remote monitoring and tension or traverse speed
control.
MAX R.D.M.C.'s calibration provides direct readout of diameter in
engineering units. Its unique sample averaging feature eliminates
problems caused by uneven rolls. Operation and setup is easy with the
full numeric keypad and menu-driven programming.
Typical Applications:
For isolated power supply, see PM41S
Roll Encoder
Diameter measurement with 3 presets
Dual roll inputs for duplex turret applications
Wind up or unwind operation
Programmable sample averaging
Programmable zero and full scale analog output points
RS-422/485 data port with selectable baud rate
Sealed NEMA 4 front panel
DIN-sized panel mounting
Non-volatile memory during power loss
Dual Roll Unwind
DYNAPAR
Multifunction Products
Expiring Roll
Standby Roll
Knife & Bumper
brand
Slip Rings
Customer
On Turret
Customer Knife
and Bumper
Control
MAX
R.M.D.C.
Roll
Encoder
Select
Input
SPECIFICATIONS
Input Power: 100 to 130 VAC or 200 to 260 VAC, 50/60 Hz, 20 VA
Accessory Power: 12 VDC @ 175 mA., short circuit protected
Diameter Counter: 5 digit with 3 presets; Programmable decimal point;
Calibrator Range: 0.0001 to 9.9999
Program Security: Individual program and preset locks
Signal Inputs: 3.5 to 15 VDC square wave @ 3.25 mA source
Outputs: 3 solid state, 100 mA sink, 28 VDC max.
Serial Communications: RS-422/485 differential, ASCII
Operating Temperature: 32 to 122 F (0 to 50 C)
Model No.
RDMC0S00
Dimensions:
Panel Dims: Cutout: 2.68" x 5.43". Thickness: 1/16" to 1/14". Depth: 5.68" min.
Maximum frequency: 20 kHz with X1 input logic
VEEDER-ROOT • EAGLE SIGNAL • DYNAPAR
144 mm
136 mm
FRONT
5.67"
5.35"
Description
MAX R.D.M.C., (115/230 VAC, selectable)
R
R.D.M.C.
10 mm
Roll diameter
measurement for
windup, unwind and
traverse control
.39"
74 mm
2.91"
132 mm
SIDE
5.20"
66 mm
13 mm
2.60"
.50"
7.05
M
U
U
N
C
O
N
L
T
F
T
I
I
7
R
O
D
U
P
C
T
S