V45450-1 VEEDER ROOT, V45450-1 Datasheet - Page 116

• Manufacturer Part Number: V45450-1
• Description: Multifunction Counter
• Manufacturer: VEEDER ROOT
• Type: Counterr

Specifications of V45450-1

• No. Of Digits / Alpha: 4
• Digit Height: 10mm
• Counting Speed: 10kHz
• Operating Temperature Range: 0°C To +55°C
• Character Size: 10mm
• Panel Cutout Width: 1.77"
• Connection Type: Screw
• Counter Type: Predetermining
• Cut Out, Panel: 1/16 DIN
• Dimensions: 1.89"L×4.33"W×1.89"H
• Display Digit Height: 10mm (Top Display), 7mm (Bottom Display)
• Display Type: LED
• Frequency, Operating: 50⁄60 Hz
• Function: Counter
• Input Type: NPN
• Mounting Type: Panel
• Number Of Digits: 6
• Primary Type: Electronic
• Standards: UL and cUL Recognized, CE Marked
• Temperature, Operating, Range: 0 to +50 °C
• Terminal Type: Screw Terminal
• Termination: Screw Terminal
• Voltage, Supply: 90 to 264 VAC
• Weight: 7 Oz.
• Input Signals Accepted From A Variety Of Sources: Dry Contact, PNP or NPN Sensors, Encoders
• Lead Free Status / RoHS Status: na

R
O
N
E
L
E
C
T
C
I
5
M
R
S
T
E
M
I
T
E
R
S
I
5.22
The SX210 timer is a microprocessor based digital timer housed in a
standard DIN style case (68mm square cutout). The small case and
front bezel require minimal panel space yet provide large, easy to use
programming keys and a .3 inch high LED display.
Eight programmable time ranges and eight output operating modes
Operating modes and all other setup functions programmed with
miniature rocker switches located on the back of the housing
Nonvolatile RAM memory retains setpoint, actual time values, and
program parameters (10 year expected life of data in memory)
NEMA 4 Hosedown Test rated
Special surface just below the display on which the function can be
marked with pen or pencil
SET and ENT keys provide access to setpoint and front panel
programmed functions
Programming changes entered via increment and decrement keys
Keypad "lock" function allows setpoint to be viewed, but does not
allow unauthorized changes
Four .3 inch red LED displays for easy readability
Flashing LED (right side of display) indicates unit is in timing cycle
and LED (left side of display) lights when programmed contacts are
energized
Two removable terminal blocks with screw gate style wire clamps
permit prewiring of panel without the timer in place and eliminate
rewiring if unit needs to be removed or replaced
Two DPDT relay outputs with five amp contact ratings - one is a set
of instantaneous contacts that energize when timing cycle starts and
remain energized until timer is reset, and the other is a set of
programmable contacts that can be programmed to turn on and off
in several operating modes
EAGLE SIGNAL
Electronic Timers
VEEDER-ROOT • EAGLE SIGNAL • DYNAPAR
brand
SX210 Microprocessor Digital Timer
SPECIFICATIONS
Time Ranges:
Operating Voltage/Frequency: A6 - 120 VAC, 50/60 Hz
Setting Accuracy:
Repeat Accuracy:
Reset Time: 15 ms
Power on Response: 200 ms max.
Operating Temperature: +32° to +122°F (0° to +50°C)
Output Rating: Relay: 5 amp (resistive), 10 to 264 VAC
Vibration: Unit function is unaffected by 2.5
Static Discharge: Unit function is unaffected by a constant 3600 volt peak,
Transient Protection: Immune to 2500 volts peak transients up to 50
Approvals: UL Recognition E96337
B6 - 240 VAC, 50/60 Hz
Current capacity derates from 7 amps at 250C to 5 amps at 500C with all
output contacts used
tude in both directions of the perpendicular mounting axes imposed from
10 to 100 Hz
60 Hz discharge applied to the grounded front plate at a relative humidity
of less than 25%
microseconds in duration
CSA Certification LR26861
Economical,
electronic, single
setpoint reset timer...
with 8 time ranges
and 8 operating
modes
Sym.
0.05% of setting or 50 ms, whichever is larger
0.001% of setting or 35 ms, whichever is larger
1
2
3
4
5
6
7
8
99 Min.: 59 Sec.
99 Hr.: 59 Min.
Maximum
99.99 Sec.
999.9 Sec.
99.99 Min.
999.9 Min.
99.99 Hr.
999.9 Hr.
Range
G
sinusoidal vibration magni-
Minimum
Setting
.01 Sec.
.01 Min.
.1 Sec.
.1 Min.
.01 Hr.
1 Sec.
1 Min.
.1 Hr.
®
RECOGNIZED
CERTIFIED
®