E5CSVR1TD500ACDC24V Omron, E5CSVR1TD500ACDC24V Datasheet - Page 6

• Manufacturer Part Number: E5CSVR1TD500ACDC24V
• Description: TEMPERATURE CONTROLLER, RELAY OP
• Manufacturer: Omron

Specifications of E5CSVR1TD500ACDC24V

• Thermocouple Type: T
• Operating Temperature Max: 55°C
• Operating Temperature Min: -10°C
• Output Voltage Max: 250VAC
• Svhc: No SVHC (15-Dec-2010)
• Accuracy: ± 0.5%
• Approval Bodies: CE, CRUus
• Colour: Black
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Operation
E5CSV
Settings before Turning ON the Power
E5CSV
Remove the E5CSV from the case to make the settings.
1. Insert the tool into the two tool insertion holes (one on the top and
2. Insert the tool in the gap between the front panel and rear case,
6
The
the SP and the
less than the SP. The
when the deviation is less than 1% FS (0.25% FS
for multi-input models). These indicators flash
during ST (self-tuning)/AT (auto-tuning).
The SP indicator lights when the setting
temperature is being displayed. The ALM
indicator lights when the alarm value 1 is
being displayed and flashes when the alarm
value 2 is being displayed.
When the power is turned ON, normally the
display will use the display items in the following
order each time the Mode Key is pressed.
one on the bottom) and release the hooks.
and pull out the front panel slightly. Grip the front panel and pull
out fully. Be sure not to impose excessive force on the panel.
(3)
(2)
indicator lights when the PV is greater than
Alarm value 1
Alarm value 2
Input shift value
(1)
Power ON
PV
SP
(1)
Deviation indicators
Press the
Press the
Press the
Press the
Press the
Temperature Controllers
Tool insertion hole
Mode indicators
indicator lights when the PV is
Mode Key
Key.
Key.
Key.
Key.
Key.
indicator (green) lights
This item is not displayed when
the Control Mode Switch 4 is OFF.
Flat-blade screwdriver
(Unit: mm)
E5CSV
0.4
When the protect switch is ON, the set
value can be changed by pressing the Up
and Down Keys while holding down the
Lock Release Key.
2.0
20 min.
Lock Release Key
3. When inserting the E5CSV, check to make sure that the sealing
Note: 1. The alarm mode switch is not provided on models without alarms.
rubber is in place and push the E5CSV toward the rear case until
it snaps into position. While pushing the E5CSV into place, push
down on the hooks on the top and bottom surfaces of the rear
case so that the hooks are securely locked in place. Make sure
that electronic components do not come into contact with the
case.
ON
2. The INIT switch is always OFF during normal operation.
ON
P
Alarm 2 is always set to the upper limit in models with two alarms.
A setting switch is not provided for alarm 2.
Control mode switches
X
1
2
INIT switch
(See note 2.)
Protect switch
3
4
5
6
The display switches each time the
Pressing the Down Key decreases the
SP/alarm value display. Keeping the Down
Key pressed continues to decrease the
display value. When the internal protect
switch is ON, press the Down Key while
holding down the Lock Release Key.
Lights when the control output is ON.
ALM1 (Alarm 1): Lights when the alarm 1
ALM2 (Alarm 2): Lights when the alarm 2
Pressing the Up Key increases the
SP/alarm value display. Keeping the Up
Key pressed continues to increase the
display value. When the internal protect
switch is ON, press the Up Key while
holding down the Lock Release Key.
PV, SP, Alarm Value, Input Shift Display
Key is pressed.
Alarm indicators
Output indicator
Alarm mode switch (See note 1.)
Down Key
output is ON.
output is ON.
Up Key
Temperature range switch