P89LPC938FA NXP Semiconductors, P89LPC938FA Datasheet - Page 41
![IC, MCU 8BIT 80C51 8K FLASH, PLCC28](/photos/19/0/190085/ge28plcc05-40_sml.jpg)
P89LPC938FA
Manufacturer Part Number
P89LPC938FA
Description
IC, MCU 8BIT 80C51 8K FLASH, PLCC28
Manufacturer
NXP Semiconductors
Datasheet
1.P89LPC938FA.pdf
(68 pages)
Specifications of P89LPC938FA
Controller Family/series
(8051) 8052
Core Size
8bit
No. Of I/o's
26
Program Memory Size
8KB
Eeprom Memory Size
512Byte
Ram Memory Size
768Byte
Cpu Speed
18MHz
Oscillator Type
External,
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
P89LPC938FA
Manufacturer:
ST
Quantity:
760
Part Number:
P89LPC938FA
Manufacturer:
NXP/恩智浦
Quantity:
20 000
Company:
Part Number:
P89LPC938FA,129
Manufacturer:
NXP Semiconductors
Quantity:
10 000
Company:
Part Number:
P89LPC938FAЈ¬129
Manufacturer:
NXP
Quantity:
1 503
Philips Semiconductors
9397 750 14051
Product data sheet
7.24 KBI
If a comparator interrupt is enabled (except in Total Power-down mode), a change of the
comparator output state will generate an interrupt and wake up the processor. If the
comparator output to a pin is enabled, the pin should be configured in the push-pull mode
in order to obtain fast switching times while in Power-down mode. The reason is that with
the oscillator stopped, the temporary strong pull-up that normally occurs during switching
on a quasi-bidirectional port pin does not take place.
Comparators consume power in Power-down and Idle modes, as well as in the normal
operating mode. This fact should be taken into account when system power consumption
is an issue. To minimize power consumption, the user can disable the comparators via
PCONA.5, or put the device in Total Power-down mode.
The Keypad Interrupt function is intended primarily to allow a single interrupt to be
generated when Port 0 is equal to or not equal to a certain pattern. This function can be
used for bus address recognition or keypad recognition. The user can configure the port
via SFRs for different tasks.
The Keypad Interrupt Mask Register (KBMASK) is used to define which input pins
connected to Port 0 can trigger the interrupt. The Keypad Pattern Register (KBPATN) is
used to define a pattern that is compared to the value of Port 0. The Keypad Interrupt Flag
(KBIF) in the Keypad Interrupt Control Register (KBCON) is set when the condition is
matched while the Keypad Interrupt function is active. An interrupt will be generated if
enabled. The PATN_SEL bit in the Keypad Interrupt Control Register (KBCON) is used to
define equal or not-equal for the comparison.
In order to use the Keypad Interrupt as an original KBI function like in 87LPC76x series,
the user needs to set KBPATN = 0FFH and PATN_SEL = 1 (not equal), then any key
connected to Port 0 which is enabled by the KBMASK register will cause the hardware to
set KBIF and generate an interrupt if it has been enabled. The interrupt may be used to
wake up the CPU from Idle or Power-down modes. This feature is particularly useful in
handheld, battery-powered systems that need to carefully manage power consumption
yet also need to be convenient to use.
In order to set the flag and cause an interrupt, the pattern on Port 0 must be held longer
than 6 CCLKs.
Rev. 01 — 25 February 2005
8-bit microcontroller with 10-bit A/D converter
© Koninklijke Philips Electronics N.V. 2005. All rights reserved.
P89LPC938
41 of 68