ADG1611BCPZ-REEL7 Analog Devices Inc, ADG1611BCPZ-REEL7 Datasheet - Page 15

• Manufacturer Part Number: ADG1611BCPZ-REEL7
• Description: IC, ANALOG SWITCH, QUAD, SPST, LFCSP-16
• Manufacturer: Analog Devices Inc
• Type: Analog Switchr

Specifications of ADG1611BCPZ-REEL7

• Analog Switch Type: SPST
• No. Of Channels: 4
• Bandwidth: 42MHz
• On State Resistance Max: 1ohm
• Turn Off Time: 105ns
• Turn On Time: 165ns
• Supply Voltage Range: 3.3V To 16V
• Design Resources: Low Cost Programmable Gain Instrumentation Amplifier Circuit Using ADG1611 and AD620 (CN0146)
• Function: Switch
• Circuit: 4 x SPST - NO
• On-state Resistance: 1.2 Ohm
• Voltage Supply Source: Single, Dual Supply
• Voltage - Supply, Single/dual (±): 3.3 V ~ 16 V, ±3.3 V ~ 8 V
• Current - Supply: 1µA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-VQFN, CSP Exposed Pad
• Multiplexer Configuration: Quad SPST
• Number Of Inputs: 4
• Number Of Outputs: 4
• Number Of Channels: 4
• Power Supply Requirement: Single/Dual
• Single Supply Voltage (min): 3.3V
• Single Supply Voltage (typ): 5/9/12/15V
• Single Supply Voltage (max): 16V
• Dual Supply Voltage (typ): ±5V
• Dual Supply Voltage (max): ±8V
• Mounting: Surface Mount
• Pin Count: 16
• Operating Temp Range: -40C to 125C
• Operating Temperature Classification: Automotive
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

TERMINOLOGY
I
The positive supply current.
I
The negative supply current.
V
The analog voltage on Terminal D and Terminal S.
R
The ohmic resistance between Terminal D and Terminal S.
R
Flatness that is defined as the difference between the maximum
and minimum value of on resistance measured over the specified
analog signal range.
I
The source leakage current with the switch off.
I
The drain leakage current with the switch off.
I
The channel leakage current with the switch on.
V
The maximum input voltage for Logic 0.
V
The minimum input voltage for Logic 1.
I
The input current of the digital input.
C
The off switch source capacitance, which is measured with
reference to ground.
C
The off switch drain capacitance, which is measured with
reference to ground.
C
The on switch capacitance, which is measured with reference to
ground.
C
The digital input capacitance.
DD
SS
S
D
D
INL
ON
FLAT(ON)
S
D
D
IN
D
INL
INH
, I
(Off)
(Off)
, C
(Off)
(V
(Off)
(I
S
(On)
INH
S
S
)
(On)
)
Rev. A | Page 15 of 16
t
The delay between applying the digital control input and the
output switching on. See Figure 31.
t
The delay between applying the digital control input and the
output switching off. See Figure 31.
Charge Injection
A measure of the glitch impulse transferred from the digital
input to the analog output during switching. See Figure 33.
Off Isolation
A measure of unwanted signal coupling through an off switch.
See Figure 27.
Crosstalk
A measure of unwanted signal that is coupled through from one
channel to another as a result of parasitic capacitance. See
Figure 28.
Bandwidth
The frequency at which the output is attenuated by 3 dB. See
Figure 29.
On Response
The frequency response of the on switch.
Insertion Loss
The loss due to the on resistance of the switch.
Total Harmonic Distortion + Noise (THD + N)
The ratio of the harmonic amplitude plus noise of the signal to
the fundamental. See Figure 30.
AC Power Supply Rejection Ratio (ACPSRR)
The ratio of the amplitude of signal on the output to the amplitude
of the modulation. This is a measure of the ability of the part to
avoid coupling noise and spurious signals that appear on the supply
voltage pin to the output of the switch. The dc voltage on the device
is modulated by a sine wave of 0.62 V p-p.
ON
OFF
ADG1611/ADG1612/ADG1613