LP2980AIM5-3.3 National Semiconductor, LP2980AIM5-3.3 Datasheet - Page 14
![no-image](/images/manufacturer_photos/0/4/469/national_semiconductor_sml.jpg)
LP2980AIM5-3.3
Manufacturer Part Number
LP2980AIM5-3.3
Description
V REG LDO +3.3V, SMD, 2980, SOT235
Manufacturer
National Semiconductor
Datasheets
1.LP2980IM5-2.5.pdf
(19 pages)
2.LP2980AIM5-3.3.pdf
(18 pages)
3.LP2980IM5-2.5.pdf
(18 pages)
Specifications of LP2980AIM5-3.3
Voltage Regulator Type
Positive Fixed LDO
Voltage, Input Max
16V
Voltage, Output Max
3.3V
Current, Output Max
0.05A
Voltage, Dropout
0.12V
Accuracy, Percentage
0.5%
Outputs, No. Of
1
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LP2980AIM5-3.3
Manufacturer:
NS
Quantity:
1 000
Company:
Part Number:
LP2980AIM5-3.3
Manufacturer:
POL-SUN
Quantity:
2 000
Part Number:
LP2980AIM5-3.3
Manufacturer:
TI/德州仪器
Quantity:
20 000
Part Number:
LP2980AIM5-3.3/NOPB
Manufacturer:
NS/国半
Quantity:
20 000
www.national.com
Application Hints
REVERSE CURRENT PATH
The power transistor used in the LP2980 has an inherent
diode connected between the regulator input and output
(see below).
FIGURE 4. LP2980 Reverse Current Path
FIGURE 2. 2.2 µF ESR Range
FIGURE 3. 10 µF ESR Range
(Continued)
01207834
01207849
01207850
14
If the output is forced above the input by more than a V
this diode will become forward biased and current will flow
from the V
occur under these conditions as long as the current flowing
into the output pin does not exceed 100 mA.
ON/OFF INPUT OPERATION
The LP2980 is shut off by pulling the ON/OFF input low, and
turned on by driving the input high. If this feature is not to be
used, the ON/OFF input should be tied to V
regulator on at all times (the ON/OFF input must not be left
floating).
To ensure proper operation, the signal source used to drive
the ON/OFF input must be able to swing above and below
the specified turn-on/turn-off voltage thresholds which guar-
antee an ON or OFF state (see Electrical Characteristics).
The ON/OFF signal may come from either a totem-pole
output, or an open-collector output with pull-up resistor to the
LP2980 input voltage or another logic supply. The high-level
voltage may exceed the LP2980 input voltage, but must
remain within the Absolute Maximum Ratings for the ON/
OFF pin.
It is also important that the turn-on/turn-off voltage signals
applied to the ON/OFF input have a slew rate which is
greater than 40 mV/µs.
Important: the regulator shutdown function will operate incor-
rectly if a slow-moving signal is applied to the ON/OFF input.
MICRO SMD MOUNTING
The micro SMD package requires specific mounting tech-
niques which are detailed in National Semiconductor Appli-
cation Note # 1112. Referring to the section Surface Mount
Technology (SMT) Assembly Considerations, it should be
noted that the pad style which must be used with the 5-pin
package is the NSMD (non-solder mask defined) type.
For best results during assembly, alignment ordinals on the
PC board may be used to facilitate placement of the micro
SMD device.
MICRO SMD LIGHT SENSITIVITY
Exposing the micro SMD device to direct sunlight will cause
misoperation of the device. Light sources such as Halogen
lamps can also affect electrical performance if brought near
to the device.
The wavelenghts which have the most detrimental effect are
reds and infra-reds, which means that the fluorescent light-
ing used inside most buildings has very little effect on per-
formance. A micro SMD test board was brought to within 1
cm of a fluorescent desk lamp and the effect on the regu-
lated output voltage was negligible, showing a deviation of
less than 0.1% from nominal.
OUT
terminal to V
IN
. No damage to the LP2980 will
IN
to keep the
BE
,