PIC18F452I/L Microchip Technology, PIC18F452I/L Datasheet - Page 77

• Manufacturer Part Number: PIC18F452I/L
• Description: IC, 8BIT MCU, PIC18F, 40MHZ, LCC-44
• Manufacturer: Microchip Technology

Specifications of PIC18F452I/L

• Controller Family/series: PIC18
• No. Of I/o's: 34
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1.5KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Core Size: 8 Bit
• Program Memory Size: 16 KWords
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

8.1
The INTCON Registers are readable and writable reg-
isters, which contain various enable, priority and flag
bits.
REGISTER 8-1:
© 2006 Microchip Technology Inc.
INTCON Registers
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
INTCON REGISTER
GIE/GIEH: Global Interrupt Enable bit
When IPEN = 0:
1 = Enables all unmasked interrupts
0 = Disables all interrupts
When IPEN = 1:
1 = Enables all high priority interrupts
0 = Disables all interrupts
PEIE/GIEL: Peripheral Interrupt Enable bit
When IPEN = 0:
1 = Enables all unmasked peripheral interrupts
0 = Disables all peripheral interrupts
When IPEN = 1:
1 = Enables all low priority peripheral interrupts
0 = Disables all low priority peripheral interrupts
TMR0IE: TMR0 Overflow Interrupt Enable bit
1 = Enables the TMR0 overflow interrupt
0 = Disables the TMR0 overflow interrupt
INT0IE: INT0 External Interrupt Enable bit
1 = Enables the INT0 external interrupt
0 = Disables the INT0 external interrupt
RBIE: RB Port Change Interrupt Enable bit
1 = Enables the RB port change interrupt
0 = Disables the RB port change interrupt
TMR0IF: TMR0 Overflow Interrupt Flag bit
1 = TMR0 register has overflowed (must be cleared in software)
0 = TMR0 register did not overflow
INT0IF: INT0 External Interrupt Flag bit
1 = The INT0 external interrupt occurred (must be cleared in software)
0 = The INT0 external interrupt did not occur
RBIF: RB Port Change Interrupt Flag bit
1 = At least one of the RB7:RB4 pins changed state (must be cleared in software)
0 = None of the RB7:RB4 pins have changed state
Note:
Legend:
R = Readable bit
- n = Value at POR
bit 7
GIE/GIEH
R/W-0
A mismatch condition will continue to set this bit. Reading PORTB will end the
mismatch condition and allow the bit to be cleared.
PEIE/GIEL
R/W-0
W = Writable bit
’1’ = Bit is set
TMR0IE
R/W-0
INT0IE
R/W-0
Note:
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
Interrupt flag bits are set when an interrupt
condition occurs, regardless of the state of
its corresponding enable bit or the global
enable bit. User software should ensure
the appropriate interrupt flag bits are clear
prior to enabling an interrupt. This feature
allows for software polling.
R/W-0
RBIE
TMR0IF
R/W-0
PIC18FXX2
x = Bit is unknown
INT0IF
R/W-0
DS39564C-page 75
R/W-x
RBIF
bit 0