PIC18F452I/L Microchip Technology, PIC18F452I/L Datasheet - Page 207

• Manufacturer Part Number: PIC18F452I/L
• Description: IC, 8BIT MCU, PIC18F, 40MHZ, LCC-44
• Manufacturer: Microchip Technology

Specifications of PIC18F452I/L

• Controller Family/series: PIC18
• No. Of I/o's: 34
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 1.5KB
• Cpu Speed: 40MHz
• No. Of Timers: 4
• Core Size: 8 Bit
• Program Memory Size: 16 KWords
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

19.3
Power-down mode is entered by executing a SLEEP
instruction.
If enabled, the Watchdog Timer will be cleared, but
keeps running, the PD bit (RCON<3>) is cleared, the
TO (RCON<4>) bit is set, and the oscillator driver is
turned off. The I/O ports maintain the status they had
before the SLEEP instruction was executed (driving
high, low or hi-impedance).
For lowest current consumption in this mode, place all
I/O pins at either V
cuitry is drawing current from the I/O pin, power-down
the A/D and disable external clocks. Pull all I/O pins
that are hi-impedance inputs, high or low externally, to
avoid switching currents caused by floating inputs. The
T0CKI input should also be at V
current consumption. The contribution from on-chip
pull-ups on PORTB should be considered.
The MCLR pin must be at a logic high level (V
19.3.1
The device can wake-up from SLEEP through one of
the following events:
1.
2.
3.
The following peripheral interrupts can wake the device
from SLEEP:
1.
2.
3.
4.
5.
6.
7.
8.
9.
10. EEPROM write operation complete.
11. LVD interrupt.
Other peripherals cannot generate interrupts, since
during SLEEP, no on-chip clocks are present.
© 2006 Microchip Technology Inc.
External RESET input on MCLR pin.
Watchdog Timer Wake-up (if WDT was
enabled).
Interrupt from INT pin, RB port change or a
Peripheral Interrupt.
PSP read or write.
TMR1 interrupt. Timer1 must be operating as
an asynchronous counter.
TMR3 interrupt. Timer3 must be operating as
an asynchronous counter.
CCP Capture mode interrupt.
Special event trigger (Timer1 in Asynchronous
mode using an external clock).
MSSP (START/STOP) bit detect interrupt.
MSSP transmit or receive in Slave mode
(SPI/I
USART RX or TX (Synchronous Slave mode).
A/D conversion (when A/D clock source is RC).
Power-down Mode (SLEEP)
2
C).
WAKE-UP FROM SLEEP
DD
or V
SS
, ensure no external cir-
DD
or V
SS
for lowest
IHMC
).
External MCLR Reset will cause a device RESET. All
other events are considered a continuation of program
execution and will cause a “wake-up”. The TO and PD
bits in the RCON register can be used to determine the
cause of the device RESET. The PD bit, which is set on
power-up, is cleared when SLEEP is invoked. The TO
bit is cleared, if a WDT time-out occurred (and caused
wake-up).
When the SLEEP instruction is being executed, the next
instruction (PC + 2) is pre-fetched. For the device to
wake-up through an interrupt event, the corresponding
interrupt enable bit must be set (enabled). Wake-up is
regardless of the state of the GIE bit. If the GIE bit is
clear (disabled), the device continues execution at the
instruction after the SLEEP instruction. If the GIE bit is
set (enabled), the device executes the instruction after
the SLEEP instruction and then branches to the inter-
rupt address. In cases where the execution of the
instruction following SLEEP is not desirable, the user
should have a NOP after the SLEEP instruction.
19.3.2
When global interrupts are disabled (GIE cleared) and
any interrupt source has both its interrupt enable bit
and interrupt flag bit set, one of the following will occur:
• If an interrupt condition (interrupt flag bit and inter-
• If the interrupt condition occurs during or after
Even if the flag bits were checked before executing a
SLEEP instruction, it may be possible for flag bits to
become set before the SLEEP instruction completes. To
determine whether a SLEEP instruction executed, test
the PD bit. If the PD bit is set, the SLEEP instruction
was executed as a NOP.
To ensure that the WDT is cleared, a CLRWDT instruction
should be executed before a SLEEP instruction.
rupt enable bits are set) occurs before the execu-
tion of a SLEEP instruction, the SLEEP instruction
will complete as a NOP. Therefore, the WDT and
WDT postscaler will not be cleared, the TO bit will
not be set and PD bits will not be cleared.
the execution of a SLEEP instruction, the device
will immediately wake-up from SLEEP. The
SLEEP instruction will be completely executed
before the wake-up. Therefore, the WDT and
WDT postscaler will be cleared, the TO bit will be
set and the PD bit will be cleared.
WAKE-UP USING INTERRUPTS
PIC18FXX2
DS39564C-page 205